Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
E63 M6 coding over diagbus error coapi 1000
06-09-2018, 21:41 PM,
Post: #1
|
|||
|
|||
E63 M6 coding over diagbus error coapi 1000
Hello,
today I update the CCC of an E63 M6 to the lastest I-Stufe with ISTPA-P v65 I have a original ICOM with MOST and the programming works fine after few trys on Port 6802. On Port 6801 they abort at the BO and CCC-A ECU. OK this step are solved. But if the coding job starts or I try a full car coding, I get COAPI 1000 error. The same problem in NCSExpert. ISTA+ works finde and the programming with ISTA-P works too...but what is the problem with ecu coding over the Diagbus? |
|||
06-09-2018, 21:52 PM,
(This post was last modified: 06-09-2018, 21:53 PM by inotherwords.)
Post: #2
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Are you trying to code it using MOST adapter or not? If so, you need to configure EDIABAS to use MOST adapter first. You can do this using EasyConnect utility.
|
|||
07-09-2018, 06:20 AM,
(This post was last modified: 07-09-2018, 06:35 AM by weby.)
Post: #3
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Ahhh ok...MOST for EDIBAS and then try it again?
But for Ista P normally I dont need this Setup, because they Switch automaticlly. They programming via MOST, but coding are for all ECUs via Diagbus. But all other ecus outside the MOST-Bus arent coded too. |
|||
07-09-2018, 08:57 AM,
Post: #4
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
Actually you can set ICOM to DiagBus or Base, you don't need to use MOST
|
|||
07-09-2018, 20:59 PM,
(This post was last modified: 07-09-2018, 21:08 PM by weby.)
Post: #5
|
|||
|
|||
RE: E63 M6 coding over diagbus error coapi 1000
And Base instead DiagBus is the right configuration to code?
Then I try it and configure the REMOTE.INI. I use in EDIBAS REMOTE Interface and fix now in my REMOTE.INI the Hosts. At BASE they is "opps_name". I fix it with my static (dhcp assign) IP of my ICOM. Thanks for this info! |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
F33 EPS repair pack FSC error | RuleNormaliai | 8 | 728 |
9 hours ago Last Post: Flash_W_88 |
|
Mini F55 EPS 4822F7 error | Alyn546 | 19 | 249 |
Yesterday, 22:09 PM Last Post: Node |
|
coding drl taillight x3 g1 with esys | kwastmichiel | 12 | 1,343 |
Yesterday, 11:57 AM Last Post: Richard_1360 |
|
BMW E71 EGS coding 8HP70 used | BS68 | 10 | 564 |
21-05-2024, 20:56 PM Last Post: Batje |
|
BMW G05. Coding(delete) Electric Tow Bar | TIGHTFIN | 3 | 104 |
21-05-2024, 15:56 PM Last Post: kimz |
|
M performance brake DSC2 SBRE coding | Ckh091020 | 4 | 383 |
19-05-2024, 06:09 AM Last Post: Ckh091020 |
|
Bmw e53 dsc coding | hero3838 | 20 | 392 |
15-05-2024, 16:00 PM Last Post: Node |
|
Coding a F80 M3 race car | PeterY | 18 | 838 |
14-05-2024, 08:38 AM Last Post: simonchs |
|
BMW E83 A1 error - MRS: No message from DSC ... | ivanp | 39 | 1,636 |
13-05-2024, 15:45 PM Last Post: ivanp |
|
BMW EOS tester (IMIB) call-up error | fatfash | 7 | 333 |
11-05-2024, 18:13 PM Last Post: fatfash |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content