[hugo325]

Hello evereybody,

This morning I wanted to change some parameters in the ECU "FEM_BODY".
Unfortunately I have this type of error:

19-04-06 12:16:27,388 [UC_TIMING] [CodingTask - vin:WBA1C11090xxxxxxx - ecu:FEM_BODY - da:0x40] com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl: ECUId:FEM_BODY_0x40 generateNCD finished [ParallelTask-96]
19-04-06 12:16:27,388 [ERROR] [CodingTask - vin:WBA1C11090xxxxxxx - ecu:FEM_BODY - da:0x40] com.bmw.psdz.tasks.base.TaskStep: problem while executing tal [ParallelTask-96]
Errors during NCD generation for CAF cafd_00000794-015_048_005: 
DataGroup ., Function .: More than one condition parameter is active: [., .]
Timestamp: Sat Apr 06 12:16:27 CEST 2019
ErrorCategory: not set ID: 303
Class: com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl
ExecutionContext={category=UNDEFINED, ecuid=(UNKNOWN,?)}
at com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl.checkNoErrors(CafEvaluatorImpl.java:97)
at com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl.executeStage(CafEvaluatorImpl.java:174)
at com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl.executeSecondStage(CafEvaluatorImpl.java:142)
at com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl.generateNcd(CafEvaluatorImpl.java:188)
at com.bmw.psdz.tasks.coding.ncd.internal.evaluation.CafEvaluatorImpl.evaluate(CafEvaluatorImpl.java:120)
at com.bmw.psdz.talexecutor.tasks.CodingTask$Preparation.generateNcds(CodingTask.java:342)
at com.bmw.psdz.talexecutor.tasks.CodingTask$Preparation.doExecute(CodingTask.java:332)
at com.bmw.psdz.tasks.base.TaskStep.execute(TaskStep.java:119)
at com.bmw.psdz.tasks.base.PrepareAndAuthenticateExecutor.executePrepareAndAuthenticateEcu(PrepareAndAuthenticateExecutor.java:100)
at com.bmw.psdz.tasks.base.SingleEcuTask.execute(SingleEcuTask.java:465)
at com.bmw.psdz.tasks.base.scheduler.RunnableTask.run(RunnableTask.java:212)
at java.util.concurrent.ThreadPoolExecutor.runWorker(ThreadPoolExecutor.java:1145)
at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:615)
at java.lang.Thread.run(Thread.java:744)

I noticed that when I changed the value "werte" of a parameter, after the "code FDL" it goes to "UNKNOWN".
I never had this problem, I do not know why I have this type of error

Has anyone ever seen this kind of thing ?

The FDL code of HU_NBT2 and BKOMBI works perfectly, I have this problem only with FEM_BODY ...

Best regards, Hugo

[SweetBMW]

It’s because you have conflicting fdl lines. It’s right there in the error. More than one parameter active

[hugo325]

A....

I just made the following changes:

Blink stop light if urgent braking

ESS_AKTIVIERBARER_AUSGANG : bremslicht_blinkend (Werte = 02)
WB_GB_ENABLE : aktiv
ESS_AKTIVIERUNG_GESCHW : wert_02 (Werte=05)

Default start&stop and save config

TCM_MSA_MEMORY : Aktiv
TCM_MSA_DEFAULT_OFF : Aktiv

Ignition of the door LEDs if the reverse gear is activated

OVT_BEI_RUECKFAHRLICHT : aktiv

Number of flashing short press

BLINKZYKLEN_ANZAHL_TIPP : Werte = 4

Number of LED flash open & close door

QUITTBLK_ENTSCHAERFEN_ANZAHL : Werte = 03 [open]
QUITTBLK_SICHERN_ANZAHL: Werte = 02 [close]

Active fog lamp in the direction of the steering wheel

C_CLC_ENA : Enable (F20)
C_BLC_ENA : Enable (F20)

KL_ENABLE_LI : KL_Ein
KL_ENABLE_RE : KL_Ein

MAPPING_ABBIEGEL_L_OUTPUT : nsw_l
MAPPING_ABBIEGEL_R_OUTPUT : nsw_r

[SweetBMW]

Try to change the start atop memory coding. Only set default or memory.

[hugo325]

I solved the problem.
I did exactly the same procedure but this time it worked ...
Surely a bug of Esys, I still do not take why I got this error.

[Batje]

SweetBMW is right, you cannot have both MSA_MEMORY & MSA_DEFAULT_OFF aktiv at the same time; it will conflict.