Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Used F10 EPS Esys problem - 3.30
22-05-2019, 13:14 PM,
(This post was last modified: 22-05-2019, 13:26 PM by willisodhiambo.)
Post: #1
|
|||
|
|||
Used F10 EPS Esys problem - 3.30
I am trying to install a used EPS motor on an F10 528. No details of source car and no hardware labels on it so I cant tell if it is correct hardware. I have attempted to code it with Esys. Two things I am finding very strange,
1. I am reading SVT Actual from ECUs (Also tried VCM), then I calculate SVT target after obtaining I-step shipment from VCM master tab, I then calculate Tal (Also tried with "HWIDS from SVTactual". Ithen notice that ALL ECUS have matching HWELs but EPS does not math HWEL!! This is hardware mismatch 2. I change I-Step shipment to before cars actual I-step shipment, same scenario, I try several I-step shipments after cars (car is 10-13-520), Same issue. Any attempt to go to any I-Step shipment other than those within 2010 results in an error. The error reads "Generating target SVT with strategy complete flash and integration level "F010-17-11-520" and "F010-11-03-500" (shipment) failed. [C324] KIS erroras logistische Teil mit dernSachnumber 9385181 is nict bestellbar [1283] Is this a hardware mismatch? Is it saying there is a part number 9385181 that does not exist? Or is the problem the fact that I selected complete flash instead of single flash? I will go back at it tomorrow so any suggestions welcome. Oh, and using cars Istep shipment calculates TAL ok but HWEL mismatch in EPS. Attempt to flash obviously results in SVK-ist does not match expected SGBMIDS for ECU EPS! And I noticed in VCM mater tab all the three I-step shipments default to cars I-step shipment, including the current I-step. Is that right? Would that be cause of my problems? |
|||
22-05-2019, 13:31 PM,
Post: #2
|
|||
|
|||
RE: Used F10 EPS Esys problem - 3.30
If you used correct EPS with part numbers according to ones given by ETK should work only with ESYS Coding via (Detect CAF for SWE) and ISTA D/Service Function/Initial Startup of EPS.
If you have different not matching part number it will NOT WORK!! Regards. |
|||
22-05-2019, 17:12 PM,
Post: #3
|
|||
|
|||
RE: Used F10 EPS Esys problem - 3.30
Any idea why in VCM mater tab all the three I-step shipments default to cars I-step shipment, including the current I-step? I think something is preventing esys from extracting current istep.
I did some experiment on another working car 1. Calculated svt target with an earlier shipment I-step. Works 100%! Can flash 2. Tried with Istep later than car, cant calculate svt target I can conclude hardware mismatch. Still need to find out why esys not identifying current istep of the vehicle in vcm master tab |
|||
22-05-2019, 21:30 PM,
Post: #4
|
|||
|
|||
RE: Used F10 EPS Esys problem - 3.30
Because somebody make wrong write of I-level?
|
|||
23-05-2019, 13:44 PM,
Post: #5
|
|||
|
|||
RE: Used F10 EPS Esys problem - 3.30
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content