Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
VCDS 17.8.1 MULTILANGUAGE FULL
18-02-2019, 19:04 PM,
Post: #401
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
when i saw this i just could not help myself , this looks a lot like the BMW inpa cable K-Dcan hardware, i had to try it , i did my FTDI chip with Mprog all good nut could not do the Atmel chip over usb , used TL866 ISP , i can program it but it revuse to write the Fuse bits no idea why but i did the code and data memory and just left the fusebits it do not match the Project files for tl866 , whel it do open vcds and say my cable need firmware 1.96 and mine is 1.95 , it updates it and all done did the TEST and i get K1 short to +12 and K2 short to +12 , and can say not pluged into car but the inpa cable do acept the programming and the VAGCOM_HWType identify it as HW44 and bootloader enabled , even VAGCOM_EEWrite do write it over usb after i programed it with tl866 , so it is not compatable or my problem is the Fuse/Lock bits , i will try with AVR
|
|||
03-03-2019, 19:09 PM,
Post: #402
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
(18-02-2019, 19:04 PM)jakesvw Wrote: when i saw this i just could not help myself , this looks a lot like the BMW inpa cable K-Dcan hardware, i had to try it , i did my FTDI chip with Mprog all good nut could not do the Atmel chip over usb , used TL866 ISP , i can program it but it revuse to write the Fuse bits no idea why but i did the code and data memory and just left the fusebits it do not match the Project files for tl866 , whel it do open vcds and say my cable need firmware 1.96 and mine is 1.95 , it updates it and all done did the TEST and i get K1 short to +12 and K2 short to +12 , and can say not pluged into car but the inpa cable do acept the programming and the VAGCOM_HWType identify it as HW44 and bootloader enabled , even VAGCOM_EEWrite do write it over usb after i programed it with tl866 , so it is not compatable or my problem is the Fuse/Lock bits , i will try with AVR Today I also tried to upload to dcan because my vcds do not have ATMEGA. The grounds and lock were set. The same effect - shorting to 12V. It seems to me that you need to reprogram GAL, HW dcan looks the same as vcds |
|||
04-03-2019, 16:00 PM,
Post: #403
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
Hello everyone, I have this interface 10.6 fw 1.81
is it possible to update it? Thanks in advance |
|||
05-03-2019, 11:59 AM,
Post: #404
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
(10-02-2019, 17:53 PM)lanman Wrote: Thank you so much for your reply BS68!! You can flash your cable over USB and use Loader v7.2 with 18.9 or even with 18.9.1 (first release) without any issues. |
|||
05-03-2019, 14:56 PM,
Post: #405
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
not working vcds in windows 7 -64bit
|
|||
16-03-2019, 23:53 PM,
(This post was last modified: 18-03-2019, 09:25 AM by bg17aw.)
Post: #406
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
Hey guys, I got VAGCOM_HWType.exe from this thread but I am not getting any info if the bootloader is available or not, is it possible I need another version of vagcom_HWType.exe?
Any ideas? The chips on the board: ATMEGA162 16AU 1648H + FT232RL + L7805CV + 16V8B My interface has a programming header - 6 pins that are connected to 6 pins of the Atmega chip, and also 2 jumpers, like I could set something on or off. I tried to depict the jumpers in the pictures attached. I am trying to update the interface to a newer version |
|||
17-03-2019, 01:03 AM,
(This post was last modified: 17-03-2019, 01:09 AM by bg17aw.)
Post: #407
|
|||
|
|||
RE: VCDS 17.8 MULTILANGUAGE FULL
(06-08-2017, 07:18 AM)fantomel Wrote: For some that do not know how to tie a programmer to interface or have programing pins here are some small PDFs with infos, Hi, the picture is no longer available, could you update the instructions please? The step-by-step PDFs are so helpful, but I noticed this part: " To do that open program PROGISP included in the pack and push the RD button" What is the pack, where is the pack that contains PROGISP? Another one I noticed is "BE SURE YOU HAVE CONNECTED CORRECT WIRES TO MISO,MOSI,SKC,RST,GND AND THAT YOU HAVE 12V ON YOUR INTERFACE. " - not sure how to get 12V on the interface? Thank you |
|||
19-03-2019, 21:25 PM,
Post: #408
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
Goodday everyone
I still have 2x old VAGCOM cables, can I still upgrade it can someone advise me, thank you. |
|||
21-03-2019, 15:48 PM,
Post: #409
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
Hello,
I have a very old VCDS clone cable. It was bricked before and recognized as USB-Serial interface. I flashed with MPROG. Now it's recognized as "Ross-Tech HEX or KEY USB interface" I checked with VAG-COM_HWType: FW: 1.78 HW: 0x44 Identification: ROSSTECH Bootloader: Enabled Tried to flash with "VAGCOM_EEWriteLang.exe". It was succesfull. But unfortunately I get error message ion VCDS: Interface not found I tried with Loader 7.0 and VCDS 18.9.0 Can anybody help what is wrong? Thanks |
|||
22-03-2019, 08:55 AM,
Post: #410
|
|||
|
|||
RE: VCDS 17.8.1 MULTILANGUAGE FULL
You must reflash atmega and use loader 7.2
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
VCDS Atmega162 license Revoked FIX | Dubstu | 0 | 206 |
18-05-2024, 06:14 AM Last Post: Dubstu |
|
frf to bin or full backup | matustn | 0 | 52 |
15-05-2024, 10:37 AM Last Post: matustn |
|
VCDS Loader (Modded) | jtanner | 5 | 611 |
06-05-2024, 18:24 PM Last Post: justdiag |
|
VCDS 23.11.0 + LOADER | benyclaudiu | 15 | 4,363 |
02-05-2024, 07:15 AM Last Post: koldplayer |
|
VIIPlusLoader-08.024.01-FULL Free for all | greenhorn | 1 | 1,805 |
22-04-2024, 19:13 PM Last Post: BIMMERSIMBA |
|
VCDS HEX V2 (china) | standaBMW | 0 | 383 |
19-04-2024, 11:32 AM Last Post: standaBMW |
|
NEW VCDS all EU language 23.03.1 | pitercie | 5 | 720 |
17-04-2024, 06:11 AM Last Post: Karlos777 |
|
Request: full VCDS scan Audi S3 2007/2008 | ries | 0 | 138 |
29-02-2024, 20:05 PM Last Post: ries |
|
MY VCDS COLLECTION - ALL YOU NEED I HOPE | fantomel | 77 | 63,546 |
25-02-2024, 11:34 AM Last Post: XuLeTZ |
|
76 PLA / 3C Lane Change - Errors on VCDS scanning only | spooky75 | 8 | 584 |
08-01-2024, 11:12 AM Last Post: spooky75 |
Users browsing this thread:
6 Guest(s)
6 Guest(s)
Return to TopReturn to Content