Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Help: how to repair vcds china cable 12.10.3
08-10-2015, 17:45 PM,
Post: #11
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Hello Matty,
thanks a lot for your message. Now I have re-flashed all again and I have again CAN:NOT READY but immediately after the test I got another message with "license not found". This happens with both 12.12.0 and 11.11.5. I will also reply asap with all the needed info. Thanks again. Cheers |
|||
08-10-2015, 19:39 PM,
(This post was last modified: 17-11-2018, 19:37 PM by mattydr67.)
Post: #12
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Check this too
Install the vcds software 11.11.5 and/or 12.12.0 Then go to About and see if its Activated No need to do a test using the tool Maybe you need to use a Antivirus Antivirus to check if you have a virus there. Who knows Lets see what info you have Good luck |
|||
08-10-2015, 19:49 PM,
Post: #13
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Hi Matty,
I have flashed again the atmega162 with firmware v.1.92 + eeprom vers 6 11.11.5-12.12.0_eeprom 512 rl.hex and used fuse/bits as 320 (not 512). Tried with both 11.11.5 and 12.12.0 and now license is fully (green color) and test is ok with K1,K2 except CAN:NOT READY, still not ready. Maybe should I connect the interface to the car now to change it from NOT READY to OK? I have a VW car with CAN (made 2006). Thanks Matty. Have a good nite. |
|||
09-10-2015, 09:52 AM,
Post: #14
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Hi Matty, I'd like to briefly reply to this previous message you sent me:
1) why should I remove R51 resistence (also if the cable is working fine?)? 2) I updated suggested ept file on ftdi by Mprog; by PonyProg2000 I updated firmware (1.92) + eeprom (vers. 6 for 11.11.5-12.12.0 eeprom 512 rl.hex) even if probably is not a 512; 3) by PonyProg2000 set fuse and bits on security and configuration bits (it should be 256b words), this time I did NOT use v. 512b words fw; 4) power supply with a proper voltage stabilizer: 12V 5) 12V power supply applied to LM7805, GND connected as pdf procedure GND of 12 V to GND of LM7805, everything works fine during the uploading/flashing procedures. 6) after every flashing and verify told me that check was successfull (ok). Hope it helps. Thanks again to all of you. Cheers, sgtp (08-10-2015, 17:21 PM)mattydr67 Wrote: First step that you have to do is to remove the R51 ( I saw this resistence soldered in your hardware ) |
|||
09-10-2015, 10:09 AM,
Post: #15
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
If your interface is not connected to the car you get can not redy. Connect your interface to the car
|
|||
09-10-2015, 10:23 AM,
Post: #16
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Will do it asap. thx
|
|||
09-10-2015, 13:47 PM,
(This post was last modified: 09-10-2015, 14:40 PM by sgtpepper67.)
Post: #17
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
(09-10-2015, 10:09 AM)GreatVortex Wrote: If your interface is not connected to the car you get can not redy. Connect your interface to the car to GreatVortex: you were right mate, just tried to connect my re-flashed cable to my VW b6 car (with CAN) and now message is "CAN: OK". I successfully tested my (ex 12.10 ver.) cable with both vcds v.11.11.5 (with long coding support) and 12.12.0: everything was perfect! I have just done for my first time a complete auto-scan, it never happened to do it completely with previous beta ver. 12.10.3 (very bad release). Thanks mates for your suggestions! PS: at the end of this story, it was "good" that RT had remotely locked my ex 12.10 cable... this has meant that I do improve to reprogram it and make it fully functional with better version as 11.11.5 and 12.12.0. Greetings! (08-10-2015, 17:21 PM)mattydr67 Wrote: @sgtpepper67 Hello Matty, please as you have some minutes free, may you kindly explain me why should I remove resistence R51 ? At the moment, I did not remove it yet and the cable is working greatly fine again (better than when it was a new brand one) after having re-programmed it. Thanks in advance for your information. Cheers, sgtp |
|||
09-10-2015, 19:37 PM,
Post: #18
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
In the end I wanna wish you as always .......Good luck
And enjoy your "newer" tool |
|||
09-10-2015, 19:41 PM,
Post: #19
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
Thanks allot Matty
|
|||
29-10-2015, 16:30 PM,
Post: #20
|
|||
|
|||
RE: Help: how to repair vcds china cable 12.10.3
My 12.12.0 vagcom cable says “unregistered interface”
Hi all I have a 12.12.0 vagcom cable with FTDI 232 RL chip. When I bought it, the first thing I did was Auto-Scan in one Audi A3 and then the license turns brown colour and Unauthorized/unregistered and I can't do anything with my cable. So I realise that I have to programme my cable and I read the MY VCDS COLLECTION - ALL YOU NEED I HOPE thread of fantomel, big thanks fantomel, and this is what I did: 1. With MProg 3.5 I flashed FTDI 232 RL chip with FT232RL.ept file inside Templates folder of MProg 3.5 Release folder. 2. With PonyProg and with LPT cable and 4 resistances of 330 ohms ( because with 1K ohms it didn't work) I flashed Atmega 162 chip with flash_192.hex and vers 6 11.11.5-12.12.0_eeprom 512 rl.hex inside 12.12.0 for BM-BL-RL folder. 3. Set the fuses as the picture. 4. I powered supply 12 V Dc to LM 7805 regulator and with the same GND to pin 25 to LPT cable, with successfull messages of every flashing procedures. 5. Install VCDS-Release-12.12.0-Installer English 512bits.exe inside 12.12.0 for BM-BL-RL folder. But when I did the Port test I have a message Status: Failed self test! and VCDS program disappears and then I have a message with Unregistered interface! Does anyone know what is happening? Thanks in advanced. [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] [img][/img] |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
J2534 cable setup odis | xMoses | 2 | 163 |
18-05-2024, 21:17 PM Last Post: Mario68 |
|
VCDS Atmega162 license Revoked FIX | Dubstu | 0 | 209 |
18-05-2024, 06:14 AM Last Post: Dubstu |
|
VCDS Loader (Modded) | jtanner | 5 | 612 |
06-05-2024, 18:24 PM Last Post: justdiag |
|
VCDS 23.11.0 + LOADER | benyclaudiu | 15 | 4,376 |
02-05-2024, 07:15 AM Last Post: koldplayer |
|
VCDS HEX V2 (china) | standaBMW | 0 | 383 |
19-04-2024, 11:32 AM Last Post: standaBMW |
|
NEW VCDS all EU language 23.03.1 | pitercie | 5 | 720 |
17-04-2024, 06:11 AM Last Post: Karlos777 |
|
Dq200 TCU made in romania or china | robot1 | 0 | 92 |
11-04-2024, 22:02 PM Last Post: robot1 |
|
Bentley flying spur led tail light repair | ahmadarifai | 1 | 97 |
15-03-2024, 07:44 AM Last Post: audi666 |
|
AUDI G85 REPAIR | rasmoka | 1 | 145 |
07-03-2024, 14:35 PM Last Post: rasmoka |
|
Request: full VCDS scan Audi S3 2007/2008 | ries | 0 | 138 |
29-02-2024, 20:05 PM Last Post: ries |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content