Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
F11 preLCI CIC-NBT retrofit
12-11-2017, 14:07 PM,
(This post was last modified: 12-11-2017, 14:19 PM by jararak.)
Post: #1
|
|||
|
|||
F11 preLCI CIC-NBT retrofit
Hi guys
have some strange problem with retrofiting NBT to CIC based car. it is 2011/09 with 6wa, logic7, combox, cic, hud I used emulator from carsystems.com.ua to not change zgw. I have now only draft instalation via temporary connection - zgw MOST connector looped and emulator MOST connected directly to ZGW, zgw can1 connected to old bus in car, can2 connected to new cables to NBT. I've also disconnected combox and looped MOST here also. Unfortunately I don't have any sound, looks Logic AMP is little bit miscounfigured and istaD shows me Kombi is not working, funny is it is working, showing me speedo, rpm, also name of songs from NBT. What is not working is HUD. Maybe my VO is maybe not codded corectly. Previous VO 1CA,1CB,1CC,1CD,230,258,2NB,2TB,316,320,337,402,418,423,428,459,481,488,494,4MR,4U2,502,508,522,524,536,548,575,609,610,612,614,615,616,620,633,677,698,6AA,6AB,6FL,6NF,6VC,6WA,710,715,760,761,775,7A2,7SP,801,851,879,8KA,8TF,8TH,8TN,8V1 Time criterion changed to 0712 Removed 6FL, 6VC, 633 Added 6NS |
|||
13-11-2017, 07:23 AM,
Post: #2
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
(12-11-2017, 14:07 PM)jararak Wrote: Hi guys ISID will never show KOMBI as active after this retrofit , if you want to access AMP - NBT - KOMBI ( MOST ring modules ) then you need to connect esys to 169.254.199.99 gateway . removing or adding FA to the car original VO doesn't make any difference if the NBT - KOMBI are not coded properly . I'm sure you have followed the instructions correctly but I have attach it for you just in case , MOST Connection is the trick in this setup |
|||
13-11-2017, 07:54 AM,
(This post was last modified: 13-11-2017, 07:54 AM by jararak.)
Post: #3
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
Regarding this schema (yes I have it) I've connected all except pdc buttons, in instruction is said, it should be connected only in case you are using touch controler which I curently don't have
so i should use connection via gateway url (should I check this IP via tool32- nbt prog?), this idea don't bite me , thanks should I use icom or rather enet cable? |
|||
13-11-2017, 08:20 AM,
Post: #4
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
(13-11-2017, 07:54 AM)jararak Wrote: Regarding this schema (yes I have it) I've connected all except pdc buttons, in instruction is said, it should be connected only in case you are using touch controler which I curently don't have unfortunately with ICOM is longer more complicated procedure , you will need to run some commands in CMD to route the traffic to the ICOM IP . Enet is 99.99% easier , and yes you need to connect to the gateway URL tcp://169.254.199.99:6801 , no tool32 is needed as this is the default IP of all Headunits . |
|||
18-11-2017, 12:34 PM,
(This post was last modified: 18-11-2017, 14:54 PM by jararak.)
Post: #5
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
NBT works like a charm, everything looks ok now but, i don't know how to setup VO. there is too much unknown variables, also TAL calculation error, funny is it works first time without issue.
is it possible there should be unchecked some options in menu tile VCM update after TAL execution?, maybe something different? |
|||
20-11-2017, 07:19 AM,
Post: #6
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
Looks I have some bullsht VO options, I removed near all what is optional and it start working, than adding one by one
thanks a lot once more time |
|||
30-11-2017, 07:35 AM,
Post: #7
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
Guys
another good question it is possible to update firmware in this way retrofited NBT in car? |
|||
30-11-2017, 07:48 AM,
Post: #8
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
|
|||
30-11-2017, 07:51 AM,
(This post was last modified: 30-11-2017, 07:58 AM by jararak.)
Post: #9
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
I try it in past, but have problem, I don't have VCM bakcup - where is this stored - i supose in IKE? do I need also IKE on table?
edit: why i should not have network cable? as I know this issues were on e90 and older cars, but I guess f10 has it already |
|||
30-11-2017, 07:53 AM,
(This post was last modified: 30-11-2017, 07:53 AM by bmwcoder75.)
Post: #10
|
|||
|
|||
RE: F11 preLCI CIC-NBT retrofit
(30-11-2017, 07:51 AM)jararak Wrote: I try it in past, but have problem, I don't have VCM bakcup - where is this stored - i supose in IKE? do I need also IKE on table? No you need a can filter/ignition signal (Carsystem has a CAN bridge that does that or some on ebay too if you search), plus ZGW. Nothing else. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content