[ruffles1986]

Need original eeprom for Clio II 1.5dci Ecu Delphi DDCR Trw. (with CAN-Bus)

I do immo off with emulator (Carlabimmo emulator) and now the car start but not increase revolutions.
In Ecu have DTC DF001 Inyector not programed, computer (i think the eprom is corrupt)

I already try to code inyector with Wurth Wow and the codes are aceppted, but i have same DTC and the car not increase revolutions.

[racin-snake]

Try reprogramming the injectors with clip mate then it should rev

and do one injector at a time some wont accept injector codes all at once

[ruffles1986]

Try reprogramming the injectors with clip mate then it should rev

and do one injector at a time some wont accept injector codes all at once

I think is problem of eeprom... when i do immo off, the ecu plastic case already are cut, then i think eprom was modified for someone that try immo off before me.

I upload the 95080 dump file to someone see that, and confirm if this are corrupt

[racin-snake]

Here is original dump plus procedure to reset correction values on ecu one injector at a time !!

[ruffles1986]

Here is original dump plus procedure to reset correction values on ecu one injector at a time !!

Thanks for shar the info, but the eeprom file that you share is for DCM 1.2 95160, i need eeprom 95080 (not 25080) for DELPHI DDCR Trw (with Can).

If you have this file, or someone have this, i'll be grateful.

[ruffles1986]

Here is original dump plus procedure to reset correction values on ecu one injector at a time !!

Thanks for shar the info, but the eeprom file that you share is for DCM 1.2 95160, i need eeprom 95080 (not 25080) for DELPHI DDCR Trw (with Can).

If you have this file, or someone have this, i'll be grateful.

Today i do diag, and see values for acelerator, potentiometer 1 and 2 have correct values. sensor 1 between 0,74 and 4,59, sensor 2 between 0,31 and 0,95. The signal is 0%.
Onlye the same DTC DF001 computer, injectors not programmed, i try program severel times but the error continues...

If the injectores are not correct programmed in this car is posible not acelerate?
i saw other cars with injectors not programed, the car start and acelerate... in this car is posible not acelerate?

Any idea??

[admiral]

If the injectores are not correct programmed in this car is posible not acelerate?
i saw other cars with injectors not programed, the car start and acelerate... in this car is posible not acelerate? in other cars not give te ..error code..iniectors code not programet.............:inlove: because,,,procedure for writing code not done.... :hiddentmi: if you make a mistake, ECU passes 1000 rpm Emergence of LED lamps lit,,,, if the codes are not written correctly,,, generated error code DF001:hiddentmi:

[racin-snake]

[/quote]

If the injectores are not correct programmed in this car is posible not acelerate?
i saw other cars with injectors not programed, the car start and acelerate... in this car is posible not acelerate?

Any idea??
[/quote]

yes if injectors are not programed the engine will not accelerate as it has no correction values for the injectors

read the labels on injectors write down codes and then program as i have shown in the word file

use only CAPITAL LETTERS WHEN CODING and there is no o just 0= zero

try recording the injectors as shown also remember no1 cylinder is the flywheel end of the engine !!

[ruffles1986]

If the injectores are not correct programmed in this car is posible not acelerate?
i saw other cars with injectors not programed, the car start and acelerate... in this car is posible not acelerate?

Any idea??
[/quote]

yes if injectors are not programed the engine will not accelerate as it has no correction values for the injectors

read the labels on injectors write down codes and then program as i have shown in the word file

use only CAPITAL LETTERS WHEN CODING and there is no o just 0= zero

try recording the injectors as shown also remember no1 cylinder is the flywheel end of the engine !!
[/quote]
Thanks mate i know in french cars normally cylinder 1 is flywheel side.
I try to coding injectors with Wurth Wow, i use Capital letters and values are between 0 and E.

I think the problem is Wow because when i look values before coding injectors i can see 3042042042021010 on four injectors.
And after coding injectors on cylinder nº1 the value not change.... then injector nº1 is not correct programmed.

My doubt now is if eeporm are corrupt maybe Wow detect other Delphi system (DCM 1.2 or TRW) and write code on incorrect adress because problem is always with nº1 injector...
When coded the injectors always saw correct coded message.

My numbers injectors:
E03592DA21408A05
54358B54AD60EB08
AC39AB172D912C8A
88356B13A91CE9C8

[admiral]

Disconect battery for more 2 hours,,ropes together (positive and negative) with a common wire,,,, wait for over 2 hours,,, conect battery poles, and try again,,,,,,,,,, PS,,,,,

This ECU is that you use this machine or any other machine is ..... If it's any other car,,,, Caution,,, year of manufacture and engine power,,,,,,,,