Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ Issue of 2011 F10 DME(MSV90)
28-12-2022, 07:12 AM,
(This post was last modified: 10-01-2023, 10:48 AM by Clusters.)
Post: #1
|
|||
|
|||
Issue of 2011 F10 DME(MSV90)
To our great seniors
My vehicle is 2011F10 N52B25. DME(MSV90) reported the following errors 134b02,133901,133204 Valvetronic servomotor short circuit was shown as an error. Valvetronic servomotor has been replaced with a new one. However, the error still exists. (The engine does not start.) Unplugged the Valvetronic servomotor connector, but the short circuit error remains. Has anyone had a similar experience and do I need to replace the DME? Any comments would be appreciated. |
|||
28-12-2022, 11:54 AM,
Post: #2
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
TRY TO REFLASH DME IF THE ISSUE STILL REPLACE IT
|
|||
28-12-2022, 12:57 PM,
Post: #3
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
You should also check the wiring before replacing DME
|
|||
28-12-2022, 13:22 PM,
Post: #4
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
you can pin out the cables directly at the dme. then check if the error is still present before you change the dme
|
|||
29-12-2022, 13:14 PM,
Post: #5
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
Many issues with these DME's.
Once you open it you usually see a leaked capacitor that damaged the board. |
|||
09-01-2023, 07:28 AM,
(This post was last modified: 09-01-2023, 08:05 AM by ga3.)
Post: #6
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
To great seniors !
This is the update after that. The MSV90 is back from repair. All initial errors are gone. And I learned the valvetronic motor, but the engine does not start. Crank does. There is spark coming out of the plug. Gas is coming because the plugs are wet. The engine will run for about 0.5 seconds, but then immediately stop. There is no error in ISTA. None of the Z11 fuses were blown. Spark plugs, valvetronic motor and coils are new. Any ideas? |
|||
09-01-2023, 10:39 AM,
Post: #7
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
you have compression, if no compression, put some oil into each cylinder and then try to start again.
engine might be flooded or else very common for the VANOS bolts to be broken. |
|||
10-01-2023, 06:40 AM,
Post: #8
|
|||
|
|||
RE: Issue of 2011 F10 DME(MSV90)
(09-01-2023, 10:39 AM) bmchicago Wrote: you have compression, if no compression, put some oil into each cylinder and then try to start again. Thank you very much. Resolved. Pistons and spark plugs were very wet. I took the time to dry them out and put a capful of oil in each cylinder. As a result, the engine started at once. It emitted a very white smoke, but has been stable since then. Thank you very much. And thanks to all of you who gave me advice. Thank you very much. |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
EGS issue on F48 auto gearbox | lalillo89 | 1 | 151 |
01-06-2024, 19:17 PM Last Post: kimz |
|
The issue from the seventh circle of hell,,, 530d | mj_mj_mj | 24 | 1,501 |
27-05-2024, 11:21 AM Last Post: mj_mj_mj |
|
ENTRYEVO Service Entry Issue | mcrussell | 4 | 193 |
26-05-2024, 01:50 AM Last Post: mcrussell |
|
Issue with F60 | Siki78 | 2 | 91 |
23-05-2024, 18:07 PM Last Post: Siki78 |
|
NBT ID4 to ID6 issue with FSC | Driss2 | 7 | 313 |
30-04-2024, 08:02 AM Last Post: stydly |
|
Kafas issue aftrer ACC Retrofit | It3_Magic | 14 | 743 |
23-04-2024, 07:44 AM Last Post: It3_Magic |
|
TMS FRM3 F10 Coding issue | mj_mj_mj | 17 | 2,210 |
16-04-2024, 09:30 AM Last Post: user_530d |
|
BMW G32 6 GT - Central Lock Issue | DaBotta | 3 | 218 |
06-04-2024, 07:44 AM Last Post: Volum |
|
I020 esys connection issue | mcrussell | 6 | 358 |
25-03-2024, 23:35 PM Last Post: vanos |
|
Harman Kardon Most issue F10 | Satia | 3 | 242 |
14-03-2024, 07:09 AM Last Post: vikro2000 |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content