[Bavrian]

Does any one know how to disable ccid 726 on g30

[TheNine90]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

[Node]

There are much more CC IDs than up to 600. Up to 2500 and a change actually (but 1xxx IDs seem to be unused).

[Bavrian]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

By double clicking on the fault in i5тд it shows the ccid number

Iv tried turning the fdl for that value to not active before the post above
but it still shows the fault on kombi

So thought I ask if anyone here has done it on g series before

[elthox]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

By double clicking on the fault in i5тд it shows the ccid number

Iv tried turning the fdl for that value to not active before the post above
but it still shows the fault on kombi

So thought I ask if anyone here has done it on g series before

it does not always do the magic. if already is not active then not possible

[Node]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

By double clicking on the fault in i5тд it shows the ccid number

Iv tried turning the fdl for that value to not active before the post above
but it still shows the fault on kombi

So thought I ask if anyone here has done it on g series before

What text EXACTLY you see on the screen for your fault? It could be you are disabling wrong CC ID.

[Bavrian]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

By double clicking on the fault in i5тд it shows the ccid number

Iv tried turning the fdl for that value to not active before the post above
but it still shows the fault on kombi

So thought I ask if anyone here has done it on g series before

What text EXACTLY you see on the screen for your fault? It could be you are disabling wrong CC ID.

These are the exact faults in the photo

The parking brake errors

[Node]

OK, this is really 726. Then I don't know. Maybe you could try disabling 725 or others nearby (should numbering be somewhat different).

[syrus]

For newer cluster the cc is as an FDL. Look for CC_MELDUNG_0726
How are you getting the correct CC ID for the fault? Ive seen most list end around CC ID 600

By double clicking on the fault in i5тд it shows the ccid number

Iv tried turning the fdl for that value to not active before the post above
but it still shows the fault on kombi

So thought I ask if anyone here has done it on g series before

By double clicking on the fault in i5тд it shows the ccid number

... is it possible, that this is depending on the version of i5тд? I just see the fault code and not the CCID number ...

[mr_nitroz]

Hi Node,

How would you operate among the below codes? so basically when there are multiple codes for the same message.

CC-ID 253
Parking Brake Failed
CC-ID 239
Parking Brake Failed
CC-ID 240
Parking Brake Failed
CC-ID 241
Parking Brake Failed
CC-ID 242
Parking Brake Failed
CC-ID 243
Parking Brake Failed

Did you successfully disable the parking brake function error? I dissabled it in KOMBI but DSC unit is still complaining about missing EMF unit messages and the error on i-drive still appear because of this. When I restart DSC unit, error is gone for 1-2 seconds and then when DSC starts it appear again. Car is F07 pre-LCI