Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
EVO hw4.1 no communication
21-03-2022, 21:21 PM,
Post: #1
|
|||
|
|||
EVO hw4.1 no communication
Hi everyone
A few months ago I bought an evo b210 with no signal on screen. There is no communication on the bench but this is what I was expecting when I was buying it. The problem is that after connecting to the uart, there is also no communication (the serial is connected properly, and is fully working, used many times in other headunits). Can anyone tell where is the problem on the PCB. thanks • EGS7/7DCT300 ISN RESET REMOTE •
• KaFAS4 (MID/HIGH) MRR, RAM VIRGIN REMOTE • • NBTevo/ENTRYNAV2/MGU VIRGIN/PATCH • • HDD -> SSD NBT/NBTevo/MGU • CARPLAY NBTevo/EN2/MGU • • FULL FSC PATCH/RETROFIT CIC, EN2,NBT, NBT2, MGU, • • REMOVE CP --> NBTEVO ID4&6/Entrynav2/MGU • UK BASED! |
|||
21-03-2022, 21:24 PM,
Post: #2
|
|||
|
|||
RE: EVO hw4.1 no communication
have you tried pinging it when connected on bench? does fan blow full speed when connected to power? or absolutely dead?
MGU Patching/Virginizing.
Feature Installer codes. Physical NBT EVO Repairs. CarPlay activations. Remote BMW Coding. [email protected] |
|||
21-03-2022, 22:10 PM,
Post: #3
|
|||
|
|||
RE: EVO hw4.1 no communication
(21-03-2022, 21:24 PM)RuleNormaliai Wrote: have you tried pinging it when connected on bench? does fan blow full speed when connected to power? or absolutely dead? Yes, I tried and the fan doesn't work either, but the "no signal" sign pops up on the screen, also i can hear the hard drive when you unplug the quadlock, and the Evo takes about 1.6 amps when connected. So something is alive, I think the power circuit is working and emmc too. • EGS7/7DCT300 ISN RESET REMOTE •
• KaFAS4 (MID/HIGH) MRR, RAM VIRGIN REMOTE • • NBTevo/ENTRYNAV2/MGU VIRGIN/PATCH • • HDD -> SSD NBT/NBTevo/MGU • CARPLAY NBTevo/EN2/MGU • • FULL FSC PATCH/RETROFIT CIC, EN2,NBT, NBT2, MGU, • • REMOVE CP --> NBTEVO ID4&6/Entrynav2/MGU • UK BASED! |
|||
22-03-2022, 08:06 AM,
Post: #4
|
|||
|
|||
RE: EVO hw4.1 no communication
(21-03-2022, 21:21 PM)DEJMIEN Wrote: Hi everyoneSounds like corrupted Jacinto side NOR flash. Not sure how to flash it via JTAG. Might be easier to desolder and program. |
|||
01-04-2022, 00:29 AM,
Post: #5
|
|||
|
|||
RE: EVO hw4.1 no communication
128MB NOR Flash chip location (HW4.1):
|
|||
10-04-2022, 09:45 AM,
Post: #6
|
|||
|
|||
RE: EVO hw4.1 no communication
Hey
I have the same problem with NBT Evo HW 3.1 B238, did you resolve problem? |
|||
13-04-2022, 09:45 AM,
Post: #7
|
|||
|
|||
RE: EVO hw4.1 no communication
(10-04-2022, 09:45 AM)kowalndm Wrote: Hey i could look in to it, but i need little bit more info. MGU Patching/Virginizing.
Feature Installer codes. Physical NBT EVO Repairs. CarPlay activations. Remote BMW Coding. [email protected] |
|||
18-04-2022, 00:11 AM,
Post: #8
|
|||
|
|||
RE: EVO hw4.1 no communication
(13-04-2022, 09:45 AM) RuleNormaliai Wrote:(10-04-2022, 09:45 AM)kowalndm Wrote: Hey Hey After starting Feature Installer and activating the code to remove Component protection, an error occurred during phase 2 of 3, after which the unit acted as if it were dead. It does not show up in E-sys, error - no communication in Tool32 and no ping in the car or via obar. |
|||
18-04-2022, 01:01 AM,
Post: #9
|
|||
|
|||
RE: EVO hw4.1 no communication
i can solve it, but i need the HU
|
|||
07-05-2022, 18:31 PM,
Post: #10
|
|||
|
|||
RE: EVO hw4.1 no communication
Hi.
NBT EVO cycle restart and no comunication E-sys and Tool32. Trying to connect via UART and see following After boloreset can't input login/pass, no answer in console. Any ideas ? Regards P.S. After boloreset the fan started working and stopped cycle rebooting |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content