Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
MSV90 cloning by hexprog
12-09-2022, 13:55 PM,
Post: #1
|
|||
|
|||
MSV90 cloning by hexprog
Hi,
Need to clone msv90 ecu. Numbers are different. Could they be cloned by hexprog? If I helped, please magic buttons thx+rep
|
|||
12-09-2022, 14:48 PM,
Post: #2
|
|||
|
|||
RE: MSV90 cloning by hexprog
yes they are interchangeable. However in my opinion it is better to read ISN from original DME and over write ISN in donor DME and reset working hours in donor DME. This requires more steps like restoring oil service interval, injector calibrations and battery replacement history and programming correct software.
Cloning DME will overwrite original part numbers/production dates etc, however it is ready to go after cloning, usually no additional steps like restoring oil service, injector calibrations and battery replacement history, or programming correct firmware/software always try to go same or higher in DME numbers when replacing DME EX: 5WK92611 TO 5WK92613+ |
|||
12-09-2022, 18:41 PM,
Post: #3
|
|||
|
|||
RE: MSV90 cloning by hexprog
Speaking of MSV90 - what is the best way of turning off rear lambda monitoring, i.e converting to EURO2 emission standard?
I've heard one way to be resetting ECU running hours and than coding two parameters. Other way is tool32 -> msv90.prg -> ecu_config_reset and than some ISTA procedure involving resetting changes or something alike? |
|||
13-09-2022, 16:45 PM,
Post: #4
|
|||
|
|||
RE: MSV90 cloning by hexprog
So it turns out, that Hexprog cant read this ecu...
For almost 99% it end with comunnication fault tryging to unlock ecu. 1 of 20 attemps are success. Have 4 backup reading but on every readings are different. Its imposible to write anyting to ecu (communication fault)... In boot mode, there are no faults when reading, but backup files are different.... If I helped, please magic buttons thx+rep
|
|||
13-09-2022, 16:57 PM,
Post: #5
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 16:45 PM)lustek Wrote: So it turns out, that Hexprog cant read this ecu... Just 3 weeks ago I successfully cloned an MSV90 for a customer. Are you using the "clone' button rather then backup and restore? |
|||
13-09-2022, 17:01 PM,
Post: #6
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 16:57 PM)AZCKNCLLC Wrote:(13-09-2022, 16:45 PM)lustek Wrote: So it turns out, that Hexprog cant read this ecu... Yes, I got error even when try to read backup, p-flash, d-flash. Try bunch of power supply, usb cables, laptops, windows 7, windows 10... every time same...communication fault when unlocking ecu. When finally hexprog unlock ecu it read without problem but every readed files are different... @AZCKNCLLC at what software version You have successfully cloned this ecu? If I helped, please magic buttons thx+rep
|
|||
13-09-2022, 17:07 PM,
Post: #7
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 17:01 PM)lustek Wrote:(13-09-2022, 16:57 PM)AZCKNCLLC Wrote:(13-09-2022, 16:45 PM)lustek Wrote: So it turns out, that Hexprog cant read this ecu... If you have autohex, you can transfer the isn. |
|||
13-09-2022, 17:19 PM,
Post: #8
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 17:07 PM)AZCKNCLLC Wrote:(13-09-2022, 17:01 PM)lustek Wrote:(13-09-2022, 16:57 PM)AZCKNCLLC Wrote:(13-09-2022, 16:45 PM)lustek Wrote: So it turns out, that Hexprog cant read this ecu... I dont have.... If I helped, please magic buttons thx+rep
|
|||
13-09-2022, 17:21 PM,
Post: #9
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 17:19 PM)lustek Wrote:(13-09-2022, 17:07 PM)AZCKNCLLC Wrote:(13-09-2022, 17:01 PM)lustek Wrote:(13-09-2022, 16:57 PM)AZCKNCLLC Wrote:(13-09-2022, 16:45 PM)lustek Wrote: So it turns out, that Hexprog cant read this ecu... Put here files from original and donor. I'll see if I can extract the isn and prepare updated file for the donor. |
|||
13-09-2022, 18:00 PM,
Post: #10
|
|||
|
|||
RE: MSV90 cloning by hexprog
(13-09-2022, 17:21 PM)AZCKNCLLC Wrote:(13-09-2022, 17:19 PM)lustek Wrote:(13-09-2022, 17:07 PM)AZCKNCLLC Wrote:(13-09-2022, 17:01 PM)lustek Wrote:(13-09-2022, 16:57 PM)AZCKNCLLC Wrote: Just 3 weeks ago I successfully cloned an MSV90 for a customer. Are you using the "clone' button rather then backup and restore? Thank you, but like i write before there are no chance to write anything to this ecu. You have hextag or hexprog? If I helped, please magic buttons thx+rep
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Solved ✔ msv90 dtc off | MPTeam | 1 | 233 |
04-11-2023, 15:53 PM Last Post: MPTeam |
|
Hexprog FRM3 Issues | BimmerExperts | 15 | 1,501 |
28-09-2023, 07:52 AM Last Post: BimmerExperts |
|
f25 n52 msv90 burning fuse f02 | PsevDo | 3 | 278 |
20-09-2023, 17:25 PM Last Post: PsevDo |
|
Solved ✔ Issue of 2011 F10 DME(MSV90) | ga3 | 7 | 764 |
10-01-2023, 06:40 AM Last Post: ga3 |
|
MSV90 cloning | MPTeam | 3 | 620 |
12-07-2022, 11:53 AM Last Post: bmchicago |
|
Bmw f30 ecu cloning | Vartaliotas | 3 | 676 |
30-03-2022, 16:01 PM Last Post: BMWzone |
|
repair dme msv90 cranking but no start | prikitiew | 6 | 952 |
15-03-2022, 10:28 AM Last Post: tintoverano |
|
2021 DME Cloning Software/Hardware | AlexRom | 5 | 1,559 |
09-02-2022, 15:43 PM Last Post: Enabled |
|
mechatronics cloning | dfitz21 | 6 | 1,042 |
30-10-2019, 07:19 AM Last Post: filipkozina |
|
CIC-MID Cloning via FTP (FSC)? | ExiizZ | 3 | 644 |
15-05-2019, 23:08 PM Last Post: ExiizZ |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content