Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Flashing NBT and KOMBI with ICOM Original
27-03-2023, 11:42 AM,
Post: #1
|
|||
|
|||
Flashing NBT and KOMBI with ICOM Original
Greetings to all. Need help, an error appears when programming NBT and KOMBI using E-Sys 3.35.3 (PSdZData FULL 4.37.42) ,connect ICOM original:
<[] Activate programming mode was not successful for: ECUId:HU_NBT_0x63 [WARN]> <[] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [WARN]> <[HU_NBT - 63] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]> <[KOMBI - 60] ECUId:KOMBI_0x60 not accessible cause could not be switched to parallel programming mode [THROWABLE]> <[] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [WARN]> It was necessary to flash (update the software version) KOMBI BMW F30. I looked at the Dependencies with the KOMBI firmware, It depends on HU_NBT, FEM_GW. I put all these blocks in TAL and when flashing errors. I know that there are some features of setting up ICOM for NBT and KOMBI programming, I once heard somewhere. There's something with setting up IP in Windows and configuring via DHCP. Help, please full LOG: Read SVT before TAL execution started. TAL execution started. <ExecutionID=2023/03/26-21:23:33.764> <[] prepareTALExecution started [PROGRESS]> <[] prepareTALExecution finished [PROGRESS]> <[] prepareVehicleForFlash started [PROGRESS]> <[] prepareVehicleForFlash finished [PROGRESS]> <MCDDiagService<id=240900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_GAC - RoutineControl GetActualConfig, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <MCDDiagService<id=240900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_GAC - RoutineControl GetActualConfig, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <MCDDiagService<id=240900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_GAC - RoutineControl GetActualConfig, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <MCDDiagService<id=84900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RDBI_FTP - ReadDataByIdentifier FlashTimingParameter, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <MCDDiagService<id=238900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_AAM - RoutineControl ActivateApplicationMode, description=error: timeout, link=HU_NBT_63_ETHERNET_63> [DIAGSERVICE]> <[] Activate programming mode was not successful for: ECUId:HU_NBT_0x63 [WARN]> <[] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [WARN]> <[HU_NBT - 63] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]> <[KOMBI - 60] ECUId:KOMBI_0x60 not accessible cause could not be switched to parallel programming mode [THROWABLE]> <[] ECUId:HU_NBT_0x63 not accessible cause could not be switched to parallel programming mode [WARN]> <[] finalizeVehicleFlash started [PROGRESS]> <[] finalizeVehicleFlash finished [PROGRESS]> <[] prepareVehicleForCoding started [PROGRESS]> <[] prepareVehicleForCoding finished [PROGRESS]> <[] finalizeVehicleCoding started [PROGRESS]> <[] finalizeVehicleCoding finished [PROGRESS]> <[] finalizeTALExecution started [PROGRESS]> <[] finalizeTALExecution finished [PROGRESS]> <TAL execution finished [TAL_EXECUTION_FINISHED]> TAL-Execution finished with status: "FinishedWithError". TAL execution finished. Duration: "3min 12s". <> Read SVT after TAL execution started. Read SVT after TAL execution finished. |
|||
27-03-2023, 12:01 PM,
Post: #2
|
|||
|
|||
RE: Flashing NBT and KOMBI with ICOM Original
With icom you need to create dhcp server to be able to flash kombi/nbt
- Secure coding (NCD 2.0) fit to FA changed (Typschlussel, Serie, Region...).
- Remove component protection MGU18/21 (only case BDC replace). - ID8.5 (SFA) conversion/ change region map. - Virgin Kafas4, MRR, RAM used. - Mgu patch, fsc custom match to vin, remove CP. - Reset ISN 7DTC, 8HP for F, G serie (include EGS7). - Write ISN MG1/MD1 with remotely. - Carplay/Android Auto MGU with/without ATM (6AE). Skype live:laquangksxd |
|||
27-03-2023, 12:13 PM,
Post: #3
|
|||
|
|||
RE: Flashing NBT and KOMBI with ICOM Original
Use simple enet cable for these modules.
|
|||
27-03-2023, 13:54 PM,
Post: #4
|
|||
|
|||
RE: Flashing NBT and KOMBI with ICOM Original
Successfully retrofit on BMW F30 335xi 248,302,3AG,430,5AG,5AS,6NS,8TH,IHKA3
|
|||
27-03-2023, 20:15 PM,
Post: #5
|
|||
|
|||
RE: Flashing NBT and KOMBI with ICOM Original
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content