[IZGOY]

In aliexpress same, in 11.11.2016 with discount codes round 120€ or less

---

yes i know.
i update one evo without issues, just rewire quadlock to OABR, pinout not is problem.
but now i try to update other one, have id5 but very old version, i want update to last.
but allways receive error and not possible update, unit work fine.

i would bought zgw for test program in table.

for example, chinese wire set, take ethernet for quadlock (after is possible rewire to OABR...) but ethernet is taken from big connector of ZGW, this is extrange, because only ethernet of OBD is take of from big connector.

ethernet for quadlock (NBT) or for OABR (EVO) is taken of same pin´s in little connector.


you take OABR from little connector or big? is my big dude, when i look all chinese adapters

for example:

not have little connector for ZGW, so ethernet is taken of BIG, same as OBD ethernet

Both are ZGW connection. Little one has ethernet wires.

you have reason i need glasses jejejejeje
i mean in CID connexion but really not possible this wire set is only for NBT.

Can Bridge in general gives ignition on signal , for NBT1 the kit in the picture is enough by adding ZGW2 ( any version works ) , but for EVO you will have to adjust the Ethernet wiring , 4 of them should be removed from the qoudlock and moved to the OABR .

its a very nice tool to have at home for people who do retrofits

Hi guys, I've collected the whole scheme on the basis of these wires and plugs, have the G12 FA, but it is impossible to calculate TAL, if someone has tested FA with TAL and FSC codes, send me to the PM, thank you

what have you got wrong?

[Jn177]

Hi guys, I've collected the whole scheme on the basis of these wires and plugs, have the G12 FA, but it is impossible to calculate TAL, if someone has tested FA with TAL and FSC codes, send me to the PM, thank you
[/quote]
what have you got wrong?
[/quote]

Yes, it works and is programmed, but had to be reworked for NBT EVO

[ir0n87]

Sadly to communicate that new bootloader V 005 in new psdzdata 3.60 is no more downgradable to V 002 to delete FSC...

If unit gets locked by trusted vin will be very hard to restore... Anyone tried to downgrade?

Did you try to downgrade 005 > 002 or 005 > 003 > 002 ?

Tried both this morning! Once u update to v5 BL no way to downgrade. So FSC codes will be impossible to delete in a "official" way.

We need to enter in QNX system or we all are fucked up with new protection!

[BhdR]

Sadly to communicate that new bootloader V 005 in new psdzdata 3.60 is no more downgradable to V 002 to delete FSC...

If unit gets locked by trusted vin will be very hard to restore... Anyone tried to downgrade?

Did you try to downgrade 005 > 002 or 005 > 003 > 002 ?

Tried both this morning! Once u update to v5 BL no way to downgrade. So FSC codes will be impossible to delete in a "official" way.

We need to enter in QNX system or we all are fucked up with new protection!

I was going to try today. It was very bad.

[ChrisF30]

Hi

Do you know the default wifi password?
Thanks

I did screen mirroring, actually it's Miracast.
As I remember there are two fdl code with "miracast" keyword, aktiv both of them, and aktiv wlan function and will work.

These two: ENT_MIRACAST & ENT_MIRACAST_DISPLAY_SETTINGS?
Are there any particular WLAN funktions to enable as well or just the MIRACAST ones?

Don't enable ENT_MIRACAST_DISPLAY_SETTINGS it will show an annoying preview of the screen mirroring menu like the ID5 menu previews on the right side of the screen but only this time it's semi-transparent on top of everything else on a screen, and presists for about a second when you navigate away from the screen mirroring option.
I think you will only need to activate WLAN_WIFI_DIRECT. This is the only one I have active but I haven't tried it with it off.
Do you guys have a WLAN antenna connected? I don't have one yet and it seems the WLAN functions are being shared over the bluetooth antenna so screen mirroring is extremely slow and drops the connection within a couple of seconds and CarPlay doesn't connect at all after the pairing process. Do you think this will be solved once I get the WiFi antenna?

I'm not sure if it is different in firmware version or country, this is the test result on my car.

1) Screen Mirroring doesn't show on menu
ENT_MIRACAST on
ENT_MIRACAST_DISPLAY_SETTINGS off

2) Screen Mirroring show on menu but no respond when select it
ENT_MIRACAST off
ENT_MIRACAST_DISPLAY_SETTINGS on

3) Screen Mirroring selectable on menu with function working
ENT_MIRACAST on
ENT_MIRACAST_DISPLAY_SETTINGS on

4) Nothing
ENT_MIRACAST off
ENT_MIRACAST_DISPLAY_SETTINGS off


I've WLAN antenna connected. If no antenna connected, my headunit even cannot make WIFI connection with my phone (no respond on that 120 seconds count-down search menu)

[Jn177]

Hi guys! I have a problem which parameter in NBTevo responsible for that would include parking sensors and a rearview camera that you could encode at the FDL, as I flash by F25, it is impossible to code for F30

[ir0n87]

U don't need any password... U should connect ad WIFI Direct and enable screen mirroring..

Hi

Do you know the default wifi password?
Thanks

I did screen mirroring, actually it's Miracast.
As I remember there are two fdl code with "miracast" keyword, aktiv both of them, and aktiv wlan function and will work.

These two: ENT_MIRACAST & ENT_MIRACAST_DISPLAY_SETTINGS?
Are there any particular WLAN funktions to enable as well or just the MIRACAST ones?

Don't enable ENT_MIRACAST_DISPLAY_SETTINGS it will show an annoying preview of the screen mirroring menu like the ID5 menu previews on the right side of the screen but only this time it's semi-transparent on top of everything else on a screen, and presists for about a second when you navigate away from the screen mirroring option.
I think you will only need to activate WLAN_WIFI_DIRECT. This is the only one I have active but I haven't tried it with it off.
Do you guys have a WLAN antenna connected? I don't have one yet and it seems the WLAN functions are being shared over the bluetooth antenna so screen mirroring is extremely slow and drops the connection within a couple of seconds and CarPlay doesn't connect at all after the pairing process. Do you think this will be solved once I get the WiFi antenna?

I'm not sure if it is different in firmware version or country, this is the test result on my car.

1) Screen Mirroring doesn't show on menu
ENT_MIRACAST on
ENT_MIRACAST_DISPLAY_SETTINGS off

2) Screen Mirroring show on menu but no respond when select it
ENT_MIRACAST off
ENT_MIRACAST_DISPLAY_SETTINGS on

3) Screen Mirroring selectable on menu with function working
ENT_MIRACAST on
ENT_MIRACAST_DISPLAY_SETTINGS on

4) Nothing
ENT_MIRACAST off
ENT_MIRACAST_DISPLAY_SETTINGS off


I've WLAN antenna connected. If no antenna connected, my headunit even cannot make WIFI connection with my phone (no respond on that 120 seconds count-down search menu)

[Jn177]

Hi guys! I have a problem which parameter in NBTevo responsible for that would include parking sensors and a rearview camera that you could encode at the FDL, as I flash by F25, it is impossible to code for F30

[840i]

Anyone played with EVO HW 3.1 yet and managed to delete certs yet?

[retrobmwtr]

Hi guys getting this error while trying flash evo
does smbd. know what the fck is this?

https://s11.postimg.org/hofh1lc2b/hata.jpg
https://s11.postimg.org/hofh1lc2b/hata.jpg