Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Renolink Support/Feedback
17-09-2019, 20:34 PM,
(This post was last modified: 17-09-2019, 20:39 PM by volavka.)
Post: #1
|
|||
|
|||
Renolink Support/Feedback
Let share your experiense about this tool
Regards BEST CHIPTUNING SERVICE BY Zenter Performance
Contact Skype: zenter-88 Facebook: https://www.facebook.com/ZenterPerformance -------------------------------------------------------------------------------------------------------------- highest Quality ChiPTuninG Files BY PTF Team https://performance-tuningfiles.com/ POWER BY TECHNOLOGY -------------------------------------------------------------------------------------------------------------- BEST CHIPTUNING SERVICE BY Jurebv Contact Skype: live:jure.coric_1 https://files.tuning-makarska.com/ -------------------------------------------------------------------------------------------------------------- - IMMO/ECU , ODO , AIRBAG , CARRADIO , TESTED SOLUTIONS UNDER MY SOFTWARE In progress TUNING STAGE1/DPF/SCR/EGR/TVA/FLAP/ START STOP OFF Software WHAT'S NEWS ! -Steering Angle Sensor Restore For LEXUS,TOYOTA,SUBARU,MITSUBISHI,VAG -Citroen DS5 Steering lock Renew/Write Code by dumps -Passat CCM Repair corrupted dump succes -VAG ECU SIMOS PCR 2.1 KM WITH CRC CORRECTED ! -IMMO OFF For NISSAN/INIFINITI with HITACHI ECU | CPU SH705X -Dacia Dashboard with Fujitsu MB96F6A6 Change km/Block Synchro Dash-ABS -=[Full WinOLS/ECM Titanium User] =- Remember! dirty hands are a sign of clean money шшш.αήkαbôôτ.Ćô.цk |
|||
Reputation: +2 - fantomel [+1] , Abou-raffik [+1] | |||
17-09-2019, 22:48 PM,
Post: #2
|
|||
|
|||
RE: Renolink Support/Feedback
first of all special thank for cartechnology owner for this helpful thread making.
hi all my friends i have problem with symbol II with ecu v42 after dead battery i try to learning ecm using renolink v182 -renolink v182 -car logan 2 2015 year -problem:virgin uch after dead battery what i do keys uch t4 logan2 sendero2....ecm learning. -read pin =read ok pin code +isk key (id key 1 and 2 with 00 00 00 00 value)!!! -connect -start learning -validate -disconnect try to start but wont to start. finally i try with uch blank icon but same any one can guide me please (there is 500 km between me and the first near dealer). thankyou in advance |
|||
18-09-2019, 09:48 AM,
Post: #3
|
|||
|
|||
RE: Renolink Support/Feedback
Airbag reset work perfect only on Twingo after reset crash must make configuration.
Renault Megane 2 card programing not work so good and make only one card valid and i use other tool. Renault Scenic 3 card program not work good so i use other tool. Steering lock virgin work good. Configuration for dashboard (Renault Scenic 3,Megane 3,Megane 4,Scenic 4 after some configuration remove + positive from acu. and reconnect) if you make mistake you will have error prog but you can make auto configuration via Renault Clip. If i helped click thanks and add reputation.
|
|||
18-09-2019, 09:51 AM,
Post: #4
|
|||
|
|||
RE: Renolink Support/Feedback
(17-09-2019, 22:48 PM)BOULEFAA Wrote: first of all special thank for cartechnology owner for this helpful thread making.If you virginize uch you Must do : write pin on uch after that learn keys and after that learn ecu to learn ecu use xml(diagnostic running) |
|||
18-09-2019, 11:48 AM,
Post: #5
|
|||
|
|||
RE: Renolink Support/Feedback
When you write Feedback or Problems write also what Renolink Version you used since are a lot of them.
If you like my post and it helped you please press
|
|||
Reputation: +2 - Abou-raffik [+1] , dabaca [+1] | |||
18-09-2019, 21:25 PM,
Post: #6
|
|||
|
|||
RE: Renolink Support/Feedback
If you virginize uch you
Must do : write pin on uch after that learn keys and after that learn ecu to learn ecu use xml(diagnostic running) thankyou brr but car take the long way to dealer sow i dont have chance to test. |
|||
08-10-2019, 16:23 PM,
Post: #7
|
|||
|
|||
RE: Renolink Support/Feedback
hi, i'm newby with this sw, i don't understand what mean those mention :" Learning key in protected mode"???
also in tdb section :"only forward without pach"?? can someone explain for us, regards |
|||
10-10-2019, 13:43 PM,
Post: #8
|
|||
|
|||
RE: Renolink Support/Feedback
|
|||
11-10-2019, 16:16 PM,
Post: #9
|
|||
|
|||
RE: Renolink Support/Feedback
hi, another issue: i have this UCH Réf: 8201068830
from Renault symbol 2007; i connect it with Renolink1.79>>uch_trans v7_1 but when i attempt to do" clear Immo Uch" it won't and give message:"can't clear immo" Regards |
|||
11-10-2019, 23:05 PM,
Post: #10
|
|||
|
|||
RE: Renolink Support/Feedback
i program second card in fluence 2017, works ok
|
|||
Reputation: +1 - justdiag [+1] | |||
« Next Oldest | Next Newest »
|
Users browsing this thread:
4 Guest(s)
4 Guest(s)
Return to TopReturn to Content