Possibly Related Threads…

***BWF*** · 13-11-2017, 14:16 PM,

I have programmed this vcds but it does not open the program. I have seen that this hardware does not have jumpers. [Image: cf5c17662859aaf9fbd34b1f35b0edf3.jpg]

[Image: cf5c17662859aaf9fbd34b1f35b0edf3.jpg]

[Image: 96e2d5060ad6253a36c9bf4b942cabfd.jpg]

Enviado desde mi Redmi 3 mediante Tapatalk

***lehasto*** · (This post was last modified: 13-11-2017, 15:36 PM by lehasto.)

Programmed HW 44 for instructions. After programming when connected to a car is not lit LED, the adapter is determined, the test fails, writes is not connected to the vehicle.
What to do ???? sad

Photo card (such as I have, from the post above) vcds 11.11

***carschrauber*** · 13-11-2017, 19:49 PM,

Saturday I programmed the same interface. The interface have a STC chip and you have to remove it. Or, I cut the pin from the T5 to STC Pin 9. After interface programming VCDS sayed interface are connected. But I test it with a battery pack and not on a car. It seems to be working.

How do you programmed the ATMEL? In your pic I can't see any soldering.

***darek_naprawa*** · (This post was last modified: 13-11-2017, 20:04 PM by darek_naprawa.)

Please tell me if this vag has hw44 or hw46.

***BWF*** · 13-11-2017, 21:17 PM,

Does anyone have any solution to this problem?

VCDS works well with the English language, but when you install Spanish it does not open the program.

It does not open with the vcds connected to the usb or not.
It also does not open without putting the V2 loader

***lehasto*** · 14-11-2017, 09:53 AM,

(13-11-2017, 19:49 PM)carschrauber Wrote: Saturday I programmed the same interface. The interface have a STC chip and you have to remove it. Or, I cut the pin from the T5 to STC Pin 9. After interface programming VCDS sayed interface are connected. But I test it with a battery pack and not on a car. It seems to be working.

How do you programmed the ATMEL? In your pic I can't see any soldering.

STC removed from the board, Atmega 162 was stitched by the AVR 910 programmer according to the proposed scheme. The interface is determined, but when 12 volts power is connected from the battery, the diode does not light sad. Re-programed already 10 times-write is not connected to the car

***zeze*** · 14-11-2017, 22:23 PM,

(13-11-2017, 21:17 PM)BWF Wrote: Does anyone have any solution to this problem?

VCDS works well with the English language, but when you install Spanish it does not open the program.

It does not open with the vcds connected to the usb or not.
It also does not open without putting the V2 loader

hi
put date of the pc back to 1/11
runasdate does not work unfortunately

regards

***lehasto*** · 18-11-2017, 10:00 AM,

(14-11-2017, 09:53 AM)lehasto Wrote:
(13-11-2017, 19:49 PM)carschrauber Wrote: Saturday I programmed the same interface. The interface have a STC chip and you have to remove it. Or, I cut the pin from the T5 to STC Pin 9. After interface programming VCDS sayed interface are connected. But I test it with a battery pack and not on a car. It seems to be working.

How do you programmed the ATMEL? In your pic I can't see any soldering.

STC removed from the board, Atmega 162 was stitched by the AVR 910 programmer according to the proposed scheme. The interface is determined, but when 12 volts power is connected from the battery, the diode does not light sad. Re-programed already 10 times-write is not connected to the car

Everything worked: D Installed a new AVR STUDIO everything was done as it should. Thanks for the software VCDS

***carschrauber*** · 18-11-2017, 17:49 PM,

(18-11-2017, 10:00 AM)lehasto Wrote:
(14-11-2017, 09:53 AM)lehasto Wrote:
(13-11-2017, 19:49 PM)carschrauber Wrote: Saturday I programmed the same interface. The interface have a STC chip and you have to remove it. Or, I cut the pin from the T5 to STC Pin 9. After interface programming VCDS sayed interface are connected. But I test it with a battery pack and not on a car. It seems to be working.

How do you programmed the ATMEL? In your pic I can't see any soldering.

STC removed from the board, Atmega 162 was stitched by the AVR 910 programmer according to the proposed scheme. The interface is determined, but when 12 volts power is connected from the battery, the diode does not light sad. Re-programed already 10 times-write is not connected to the car
Everything worked: D Installed a new AVR STUDIO everything was done as it should. Thanks for the software VCDS

Congratulation!

***uh60*** · 20-11-2017, 19:58 PM,

(13-11-2017, 20:04 PM)darek_naprawa Wrote: Please tell me if this vag has hw44 or hw46.

This is HW46, works quite good, but the 7805 builds up a lot of heat. Better to find a 44 one but this one also works really well but you might have to change the 7805 quite a couple of times in its lifetime.

Possibly Related Threads…
Thread		Author	Replies	Views	Last Post
	VCDS Atmega162 license Revoked FIX	Dubstu	0	249	18-05-2024, 06:14 AM Last Post: Dubstu
	frf to bin or full backup	matustn	0	57	15-05-2024, 10:37 AM Last Post: matustn
	VCDS Loader (Modded)	jtanner	5	665	06-05-2024, 18:24 PM Last Post: justdiag
	VCDS 23.11.0 + LOADER	benyclaudiu	15	4,544	02-05-2024, 07:15 AM Last Post: koldplayer
	VIIPlusLoader-08.024.01-FULL Free for all	greenhorn	1	1,857	22-04-2024, 19:13 PM Last Post: BIMMERSIMBA
	VCDS HEX V2 (china)	standaBMW	0	405	19-04-2024, 11:32 AM Last Post: standaBMW
	NEW VCDS all EU language 23.03.1	pitercie	5	739	17-04-2024, 06:11 AM Last Post: Karlos777
	Request: full VCDS scan Audi S3 2007/2008	ries	0	142	29-02-2024, 20:05 PM Last Post: ries
	MY VCDS COLLECTION - ALL YOU NEED I HOPE	fantomel	77	63,611	25-02-2024, 11:34 AM Last Post: XuLeTZ
	76 PLA / 3C Lane Change - Errors on VCDS scanning only	spooky75	8	598	08-01-2024, 11:12 AM Last Post: spooky75

Contact Us