Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
NBT Evo bench test can not ping
03-12-2023, 15:25 PM,
Post: #1
|
|||
|
|||
NBT Evo bench test can not ping
Hi,
I have a Nbt Evo HW 4.1 connected to a ZGW 4sk(2x Ethernet ports) via OABR connector. I'm using a can bus board to send ignition and vin signal to wake both ZGW and HU. ZGW OABR -------------------------------- 11--------TX+ ----------17 12--------TX- ---------- 19 9 ---------RX+ ---------18 18--------RX- -----------20 Screen is on, can see both on e-sys. Can code HU. My problem is that HU ethernet is not working. if I try to ping 169.254.199.99 it says host unreachable. And of cource it is not possible to flash the HU. Tried connect OABR to rj45 and the ip 169.254.199.99 is presented in my network and able to ping the ip. Of course HU ethernet is disconnected from ZGW side though. RJ45 OABR -------------------------------- 1--------TX+ ----------17 2--------TX- ---------- 19 3--------RX+ ---------18 6--------RX- -----------20 Do I missing something? Thanks in advance |
|||
03-12-2023, 17:24 PM,
Post: #2
|
|||
|
|||
RE: NBT Evo bench test can not ping
Attach a picture of which connector in the ZGW
|
|||
03-12-2023, 18:49 PM,
Post: #3
|
|||
|
|||
RE: NBT Evo bench test can not ping
|
|||
03-12-2023, 19:53 PM,
Post: #4
|
|||
|
|||
RE: NBT Evo bench test can not ping
(03-12-2023, 15:25 PM)alsamaraee Wrote: Hi, Had the same issue with ZGW Mid flashed to 4SK. Once I've used High flashed to 8SK, issue went away. Somehow ZGW doesn't route ethernet HU side. Didn't care to look much into it as I had 2-3 zgws laying around.. Use tool32 and run zgw01.prg -> STATUS_ETHERNET_INFORMATION Post the output I like Objective-C |
|||
03-12-2023, 20:40 PM,
Post: #5
|
|||
|
|||
RE: NBT Evo bench test can not ping
Hello walkernight88,
Here it is --------------------------------------------------------------------- apiJob("ZGW_01","status_ethernet_information","","") Satz : 0 OBJECT = zgw_01 SAETZE = 1 JOBNAME = status_ethernet_information VARIANTE = ZGW_01 JOBSTATUS = UBATTCURRENT = -1 UBATTHISTORY = -1 IGNITIONCURRENT = -1 IGNITIONHISTORY = -1 Satz : 1 STAT_OBD_AKTIVIERUNGSLEITUNG = 1 01 . STAT_OBD_AKTIVIERUNGSLEITUNG_TEXT = OBD Aktivierungsleitung: ein STAT_OBD_LINK = 1 01 . STAT_OBD_LINK_TEXT = OBD Link: ein STAT_HU_AKTIVIERUNGSLEITUNG = 1 01 . STAT_HU_AKTIVIERUNGSLEITUNG_TEXT = HU Aktivierungsleitung: ein JOB_STATUS = OKAY _REQUEST = 3 Bytes 0000 : 22 40 31 "@1 _RESPONSE = 6 Bytes 0000 : 62 40 31 01 01 01 b@1... --------------------------------------------------------------------------------- |
|||
03-12-2023, 20:46 PM,
Post: #6
|
|||
|
|||
RE: NBT Evo bench test can not ping
I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
• EGS7/7DCT300 ISN RESET REMOTE •
• KaFAS4 (MID/HIGH) MRR, RAM VIRGIN REMOTE • • NBTevo/ENTRYNAV2/MGU VIRGIN/PATCH • • HDD -> SSD NBT/NBTevo/MGU • CARPLAY NBTevo/EN2/MGU • • FULL FSC PATCH/RETROFIT CIC, EN2,NBT, NBT2, MGU, • • REMOVE CP --> NBTEVO ID4&6/Entrynav2/MGU • UK BASED! |
|||
03-12-2023, 20:52 PM,
Post: #7
|
|||
|
|||
RE: NBT Evo bench test can not ping
|
|||
03-12-2023, 21:36 PM,
Post: #8
|
|||
|
|||
RE: NBT Evo bench test can not ping
(03-12-2023, 20:52 PM)alsamaraee Wrote:(03-12-2023, 20:46 PM)DEJMIEN Wrote: I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29. and what about STATUS_ETHERNET_REGISTER_LESEN? does the registry show a 100mbps link between HU and ZGW? I like Objective-C |
|||
03-12-2023, 21:53 PM,
Post: #9
|
||||||||||
|
||||||||||
RE: NBT Evo bench test can not ping
(03-12-2023, 21:36 PM)walkernight88 Wrote:(03-12-2023, 20:52 PM)alsamaraee Wrote:(03-12-2023, 20:46 PM)DEJMIEN Wrote: I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
|