Unfortunately we do not accept new members for free, Now яёgїsтядтїои cost 30€, if you are interesting Send Email to [email protected]
NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
|
19-08-2026, 17:18 PM,
Post: #1
|
|||
|
|||
|
NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
Hey guys,
Tried to ратсн the boot IFS on the Jacinto processor of my NBT EVO ID5 (3.1) and now the unit is dead - no fan, "NO SIGNAL" on CID, no connection in ё_5у5. Is there any way to restore boot IFS on Jacinto if there's no connection at all? I tried UART but got no response - might be doing something wrong there. Any advice appreciated, thanks! +REP & Thanks = motivation
 |
|||
|
|
19-08-2026, 17:21 PM,
(This post was last modified: 19-08-2026, 17:22 PM by Cro.)
Post: #2
|
|||
|
|||
|
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
yeah, it can be recovered but required to ship the HU
Motorrad f5с retrofit, Motorrad BMS IMMO solutions
MRR 0x149 retrofit, EGS7 recover via J2534 ISN 5ёяvїcё, EGS ISN reset (including EGS7 via OBD) Custom NBTEvo solutions, Physical NBTEvo repairs MGU solutions (including CP/AA activation via SSH) MG1 f5с retrofit by OBD, f5сs rejected by tuning repair Remote coding 5ёяvїcёs +REP and THANKS if I have helped you |
|||
|
|
|
19-08-2026, 18:15 PM,
Post: #3
|
|||
|
|||
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
(19-08-2026, 17:21 PM)Cro Wrote: yeah, it can be recovered but required to ship the HU Thanks for the reply! Just to clarify - is that because the Jacinto NOR flash chip needs to be desoldered and reprogrammed off the board? And where would I need to ship it to? +REP & Thanks = motivation
|
|||
|
|
|
20-08-2026, 05:55 AM,
Post: #4
|
|||
|
|||
|
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
to someone who can fїж it
Motorrad f5с retrofit, Motorrad BMS IMMO solutions
MRR 0x149 retrofit, EGS7 recover via J2534 ISN 5ёяvїcё, EGS ISN reset (including EGS7 via OBD) Custom NBTEvo solutions, Physical NBTEvo repairs MGU solutions (including CP/AA activation via SSH) MG1 f5с retrofit by OBD, f5сs rejected by tuning repair Remote coding 5ёяvїcёs +REP and THANKS if I have helped you |
|||
|
|
|
21-08-2026, 21:48 PM,
Post: #5
|
|||
|
|||
|
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
Write both V850 and EMMC dumps if you have correct tools.
Replace HDD also after HU alive EVO ID4/5/6 dumps: EVO dump and EMMC !!! & f5с
MG1 (BDC3): remote start 1CR active remotely MDG1 pre 06/20 OBD циLoск: send me 8Mb flash file All MDG1 Clone, confirm engine start OK: send me 8Mb flash file, 512kb/768kb Eeprom files |
|||
|
|
|
21-08-2026, 22:55 PM,
Post: #6
|
|||
|
|||
|
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
You need tools to write EMMC and also V850 most likely. This should get the unit back running. I have the tools and i do it on a daily basis, other people do it too. You can either buy the tools and do it yourself, provided you have the correct dumps or send it to someone.
|
|||
|
|
![[+]](https://cartechnology.co.uk/images/CarTechnologyTheCure/collapse_collapsed.png)
|
23-08-2026, 18:54 PM,
Post: #7
|
|||
|
|||
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
(21-08-2026, 22:55 PM)painsage Wrote: You need tools to write EMMC and also V850 most likely. This should get the unit back running. I have the tools and i do it on a daily basis, other people do it too. You can either buy the tools and do it yourself, provided you have the correct dumps or send it to someone. Thanks for the info! If I understand correctly, the eMMC is on the OMAP side - in my case it looks like I wiped a рдятition on the Jacinto side, and the unit does not boot at all now. I have already ordered a programmer and I am going to try recovering the Jacinto flash myself. Shipping the unit abroad for repair is not really worth it for me - it would be cheaper to just buy another used unit at that point. Also, if anyone has a 128Mb Jacinto flash dump they would be willing to share, I would really appreciate it. +REP & Thanks = motivation
|
|||
|
|
|
20-09-2026, 14:45 PM,
Post: #8
|
|||
|
|||
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
(23-08-2026, 18:54 PM)Asp1DD Wrote:My signature(21-08-2026, 22:55 PM)painsage Wrote: You need tools to write EMMC and also V850 most likely. This should get the unit back running. I have the tools and i do it on a daily basis, other people do it too. You can either buy the tools and do it yourself, provided you have the correct dumps or send it to someone. 
EVO ID4/5/6 dumps: EVO dump and EMMC !!! & f5с
MG1 (BDC3): remote start 1CR active remotely MDG1 pre 06/20 OBD циLoск: send me 8Mb flash file All MDG1 Clone, confirm engine start OK: send me 8Mb flash file, 512kb/768kb Eeprom files |
|||
|
|
|
21-09-2026, 05:05 AM,
Post: #9
|
|||
|
|||
|
RE: NBT EVO ID5 3.1 - Jacinto boot flash bricked, any way to recover?
Do you shill have ssh acces to unit to 169.254.199.99?
Creator of FlashXTool Web - link Whatsapp : +40741888845 |
|||
|
|
|
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content
