[Willail]

What not work? Antenna is working? Can bus is working?

Hello, i have a clone carprog using solfware 7.28. Since i received it, it is impossible to read eeproms 95160 and 24cxx. I so used the software with airbag, but the ID of the Eproom is not recognised. The eprooms were desolder from the pcb and i used the A4 and A5 adapters provided with carprog. I have verified that the wires were correct with a multimeter (continuity test). I don't know if the changes of the 4 IC will help to read eprooms. I very dissapointed

I don't test if antenna and CAN bus are working? How do i make it?
Thanks for your reply

---

Look one Page back post nr. 780 in this thread
https://cartechnology.co.uk/showthread.p...#pid347509

Most people flash to 8.21 and make rework like on many pictures in this thread

Hello, thank you for this reply. I will send you some picture of my carprog. Then , you will tell me if it is a good pcb. Can you give the main changes to make at the rear of the pcb because on the pictures, it is not easy to understand (remove some capacitors, remplace by a what? repair the hole line missing?
Thanks

---

i tested it and work perfect.

Hello, could you explain me the changes that you made on your carprog for held reading and writing eprooms? Add a 120 ohm resistor and change the 4 iC 74HC125D by 74HCT125M?

Here we go this is good start and yes change 4x 74HC125D to 74HC125M i will post some pictures of the other mods shortly hope this helps don't forget to thanks and rep those who have helped you

Hello, thank for your reply. Do you know where i can buy some good 74HCT125M?
It is possible to buy on Ebay? Some friends say that the components on Ebay are not original and are bad. Thanks

i not change 4x 74HC125D to 74HC125M and well read-write 24cxx,95x without any problem.

Hello,

Thank you for the picture.
Could you send me a picture of the rear of your carprog?

Thank you

[kastanka]

here you are.    

[Willail]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

[dil6222]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

not sure if you change firmware whether it helps eeprom reading but it gives more functions if you update to 7.81 what mods have you done so far now then?

[kastanka]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

I not changed,I bought with the new firmware.

[Willail]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

I not changed,I bought with the new firmware.

Hello, you will find the photos of my clone carprog 7.28. You will see that i have not make any modifications on the pcb (only the white wire for ground). When i compare your carprog with my carprog, i notice that you have make some modifications (removal capacitors, add of a resistor and may be change the value of resitor). Did you have change the value of the resistor R38? Could you please explain me your modifications? Did you have only remove the capacitors C33 and C36? i find a note where someone add a wire to connect C21 and C17
Thanks

[dil6222]

Hi guys
My carprog v8.21/10.0.5
He need password

What can I do
He said enter password
8 characters maximum
How i can solved

Sounds like it needs activation does HWID come up in the box that needs password ? Post name and hwid that carprog gives and we can activate

[kastanka]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

I not changed,I bought with the new firmware.

Hello, you will find the photos of my clone carprog 7.28. You will see that i have not make any modifications on the pcb (only the white wire for ground). When i compare your carprog with my carprog, i notice that you have make some modifications (removal capacitors, add of a resistor and may be change the value of resitor). Did you have change the value of the resistor R38? Could you please explain me your modifications? Did you have only remove the capacitors C33 and C36? i find a note where someone add a wire to connect C21 and C17
Thanks

.i'm so sorry but , I do not remember how I did it,i only did what I found here on the forum.( sorry i no speak amerikano,i use translater)

[Willail]

here you are.

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

I not changed,I bought with the new firmware.

Only a question what version of software do you have with your carprog and the version of your lib. file? For me,it is the 7.28 with bin.file 081105CAR001773I

Hello, you will find the photos of my clone carprog 7.28. You will see that i have not make any modifications on the pcb (only the white wire for ground). When i compare your carprog with my carprog, i notice that you have make some modifications (removal capacitors, add of a resistor and may be change the value of resitor). Did you have change the value of the resistor R38? Could you please explain me your modifications? Did you have only remove the capacitors C33 and C36? i find a note where someone add a wire to connect C21 and C17
Thanks

.i'm so sorry but , I do not remember how I did it,i only did what I found here on the forum.( sorry i no speak amerikano,i use translater)

[Willail]

Hello

Thank you for the picture. i will send you the photos of my carprog this afternoon, it was a little different. Do you have changed the firmware of your carprog?
Thanks

I not changed,I bought with the new firmware.

Only a question what version of software do you have with your carprog and the version of your lib. file? For me,it is the 7.28 with bin.file 081105CAR001773I

Hello, you will find the photos of my clone carprog 7.28. You will see that i have not make any modifications on the pcb (only the white wire for ground). When i compare your carprog with my carprog, i notice that you have make some modifications (removal capacitors, add of a resistor and may be change the value of resitor). Did you have change the value of the resistor R38? Could you please explain me your modifications? Did you have only remove the capacitors C33 and C36? i find a note where someone add a wire to connect C21 and C17
Thanks

.i'm so sorry but , I do not remember how I did it,i only did what I found here on the forum.( sorry i no speak amerikano,i use translater)

Hello, yesterday i have made these modifications but it doesn't work :
- removal of 2 capacitors
- change the value of the resistor
- add a resistor like the photo

Do you know what i can do more. Thank you