Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ CAS 4 platform / bench - no ignition
04-04-2022, 18:28 PM,
(This post was last modified: 04-04-2022, 18:32 PM by Clusters.)
Post: #11
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
(02-04-2022, 12:26 PM)Cowboy Wrote: Hello colleagues Do you have Emergency starting coil I have same bench without ELV. Please, Press the Buttons and if This post help or is usefull for you! Not is needed write just only thanks in Threads
|
|||
04-04-2022, 18:44 PM,
Post: #12
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
Yes, I have an emergency start coil
|
|||
05-04-2022, 10:52 AM,
Post: #13
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
You could always fake the "ignition" of the CAS4, since the KL15 is brought high (+12v) when a ignition is detected then just power with the "battery" (+12v) connection and use a separate switch is it bothers you.
I have an self build emulator and it works with both E and F series (switched), its currently powering a ZGW (for coding an flashing modules), but I have had a kombi, jbbr, HUD, TV, NBT, Controller, icm, fds module and auto gear selector all plugged in and they all power on and can be seen in e-sys. For KL15 "ignition", I just use a normal 12v power and that works perfectly well, all modules power on and stay alive. |
|||
05-04-2022, 16:57 PM,
Post: #14
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
My idea was to build a bench that would work as much as possible like a real car. I spent some time on it, not looking for shortcuts. I prepared the whole project so that in the future it was possible to add other modules (if necessary), so I did not buy a ready platform for CAS4. At the moment it can be said that the problem is solved because CAS is put into assembly mode and does not check the ELV. KL15 and Wakup work as in normal mode, i.e. with the start / stop key. Of course, in the future I will work on making ELV also work.
|
|||
06-04-2022, 07:49 AM,
Post: #15
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
Ok, cool, I have a full cas3 system (as well as the emulator) and used a elv emulator, that works ok too.
Good luck. |
|||
14-04-2022, 09:30 AM,
Post: #16
|
|||
|
|||
RE: CAS 4 platform / bench - no ignition
Hello!
The problem is completely solved. It was enough to replace the ELV with another one (the previous one was incorrect). By the way, I found out that there is no virgin ELV required for CAS4. Now, after changing the ELV to another CAS, it works in normal mode without any problems. I would like to thank colleague "Tombo" and "golffwmb" again for their help in solving the problem. Regards! |
|||
Reputation: +1 - johann74270 [+1] | |||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
MGU Bench connection | kimz | 4 | 458 |
22-04-2024, 17:06 PM Last Post: kimz |
|
F10 Headlight Test Platform | DaBotta | 1 | 199 |
04-04-2024, 21:11 PM Last Post: DaBotta |
|
Test bench Connection to CAN ECU's | HaakonA | 3 | 312 |
03-04-2024, 07:24 AM Last Post: sixcode |
|
Tool for bench read 8hp | Garryq | 9 | 1,674 |
26-03-2024, 09:32 AM Last Post: skywoker |
|
Bosch MEVD172H bench backup | mrproper | 1 | 280 |
23-03-2024, 18:43 PM Last Post: Ratnik1990 |
|
ENAV2 bench activation | Airbus | 10 | 962 |
25-02-2024, 08:17 AM Last Post: jb2005 |
|
Motronic 3.3.1 bench | jaramillo | 3 | 215 |
13-02-2024, 05:12 AM Last Post: 2013m5 |
|
Dde Coding/flash with esys in bench? | ruben_17non | 0 | 203 |
08-02-2024, 21:28 PM Last Post: ruben_17non |
|
Entrynav2 - Trying to Trigger Component Protection on Bench | 2002JCW | 5 | 565 |
30-01-2024, 16:44 PM Last Post: DEJMIEN |
|
NBT display on bench without unit | djordan | 4 | 367 |
15-01-2024, 08:08 AM Last Post: Powerlab |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content