Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
G30 Entrynav2 - rear camera retrofit problem
25-01-2024, 10:04 AM,
Post: #11
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
(24-01-2024, 07:47 AM)egyclick Wrote: You're in the same boat with me, also did one, first time I didn't mounted ENT switch, I mounted it after seeing no video was showing on navi, car is updated/coded. Although in official bmw retrofit pdf it shows that Entrynav2 it supports 3AG, I haven't seen actually one with this navi + 3AG camera that works so unless you guys really came across, this makes me believe that it might not be suported and requires nbt evo head unit. I have seen entrynav2 with 3AG so I believe it is possible (24-01-2024, 09:06 AM)larshutten Wrote: I did one couple of weeks ago. After Ethernet switch and wiring according to correct diagram it worked without issues. I will check that if ATM is working. Wires should be on correct pins. In SA606 ATM is connected to BDC, not HU and I have seen pins there. That's why I had to add ethernet switch. (24-01-2024, 16:13 PM)Fx82 Wrote: Do you have the p/n for the ethernet switch? 61358706459 (24-01-2024, 21:35 PM)markodsk Wrote: Try adding 5DM instead of 3AG to FA and try to calculate TAL. You should see ICAM show up in the modules list and then you can VO code the car and necessary modules (HU_Entrynav2, ACSM5, ICAM, USS (PDC module), BDC_BODY2/3) Interesting. I will check that too. I have checked FDLs after VO coding 3AG and everything was coded corectly for ICAM. |
|||
25-01-2024, 16:34 PM,
Post: #12
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
What about Mini with entrynav2 and 8.8" monitor? Will a vin help?
MGU virgin and patching in Europa.
Secure coding 2.0 Feature installer codes |
|||
26-01-2024, 11:40 AM,
(This post was last modified: 26-01-2024, 11:41 AM by hamzettin.)
Post: #13
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
Hello, check your gateway table in bdc and Coding ACSM with 3AG
|
|||
30-01-2024, 20:56 PM,
Post: #14
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
@Krysiaman: Have you resolved the issue?
|
|||
02-02-2024, 07:59 AM,
Post: #15
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
Not yet. Been busy lately and didn't have time to deal with it.
|
|||
13-02-2024, 08:16 AM,
Post: #16
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
|
|||
13-02-2024, 09:42 AM,
Post: #17
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
Short answer:
Change your HU to a unit whose HWEL begins with "5" and version 002.001.005 Long answer: I encountered the same problem when I wanted to get carplay on my F44. I installed several HU, but got a problem with the rear camera. After a lot of investigation, it turned out that not all enavevo can work with ICAM via Ethernet. I found that HU with HWEL starting with “3” and “4” (I tried 000036CF and 000040E7) are not suitable for work. However, HU with HWEL starting with 5 work perfectly. I tested 00005D1C and 00005D18 (with MOST connector). Also, all suitable units had version HWEL 002.001.005, perhaps it’s worth focusing on this |
|||
13-02-2024, 21:44 PM,
Post: #18
|
|||
|
|||
RE: G30 Entrynav2 - rear camera retrofit problem
There are exacty 8 EntryEvo-HWEL´s on the market, that do not support ETH.
This has nothing to do Version 2 or 5! 36CF supports ETH and should work - doesn´t depend on the HWEL-Version. It also supports ETH with Version 002.xxx.xxx 40E7 does not support ETH. 5D1C and 5D18 supports ETH. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content