Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Bmw g11 Zgw failed during programming. Need help!
06-10-2017, 14:48 PM,
(This post was last modified: 06-10-2017, 15:36 PM by pweber84.)
Post: #1
|
|||
|
|||
Bmw g11 Zgw failed during programming. Need help!
Hi guys,
Friend of mine used enet for programming with ista-p. ZGW flash failed afer boot loader. Does anyone can tell me how to flash it now? There's no connection with the car. Car looks like in sleep mode. NO Terminal 15 etc. I know we need to rebuild FA. Can any one do it remotely? He only has ENET not ICOM. Is ICOM necessery? Please I need your help. Thanks. |
|||
06-10-2017, 16:20 PM,
Post: #2
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
I do not know g cars if it was a f car i would try to:
Disconnect the battery,wait 30 minutes and then try to code any unit other then zgw , i said code not flash. That should wake the car. Is not good to flash bmw cars without ICOM. (06-10-2017, 14:48 PM)pweber84 Wrote: Hi guys, |
|||
06-10-2017, 17:06 PM,
Post: #3
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
It's not ZGW, but BDC2 module.
You can try to run ista-p again and see if reanimate bdc. If it doesn't then you have to flash it with e-sys. |
|||
06-10-2017, 17:56 PM,
(This post was last modified: 06-10-2017, 17:58 PM by pweber84.)
Post: #4
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
Ok, but how to flash it with ESYS? Can I use ENET? Or I need ICOM, it's BDC2_GW
I've attached ESYS tree with modules, after READ them. Can anyone connect remotely and flash it? I have TeamViewer open. |
|||
06-10-2017, 18:08 PM,
Post: #5
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
|
|||
06-10-2017, 18:19 PM,
Post: #6
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
(06-10-2017, 17:56 PM)pweber84 Wrote: Ok, but how to flash it with ESYS? Can I use ENET? Or I need ICOM, it's BDC2_GW HWEL Actual and Target should match (Black). You need to change to correct Shipment I-Step. |
|||
06-10-2017, 18:31 PM,
Post: #7
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
The I stage is not true.
It must be calculated exactly. |
|||
06-10-2017, 18:39 PM,
(This post was last modified: 06-10-2017, 18:44 PM by pweber84.)
Post: #8
|
|||
|
|||
RE: Bmw g11 Zgw failed during programming. Need help!
(06-10-2017, 18:19 PM)Almaretto Wrote:(06-10-2017, 17:56 PM)pweber84 Wrote: Ok, but how to flash it with ESYS? Can I use ENET? Or I need ICOM, it's BDC2_GW Can you please elaborate how to do it? I've attached 3 screens. Whatever I-STEP level I input it gives me these error. I also attached a report from ISTA-P when it failed. PDF doc. |