[hojo29]

Hojo29 your PM box is full. Anyway Thank you for your offer, I really appreciated this.

I think I did it, I was able to reflash BDC_GW

I did calculate SVT Target (SVT_soll) agin and checked the box that says "HW-IDs from SVTactual" and then Saved it, after it it went well.

But still few modules are red and don't know why. But car Ignition is working ok now.
I will use ICOM to flash all other ECUs, complete programming.

BTW, the car has brand new ECU (DME) replaced and installed, what should I check when I want to program it?

If new DME was installed then simply assign a new CAFD and encode DME.
And if PM is full then you can delete the old messages and then goes again.

[pweber84]

Ok, after diagnosing with ISTA-D all ECUs are green, but with ACSM and DME there is no connection (RED). Do you know why? Should I reflash whole car with ESYS or ISTA-P?

I will fire up ISTA-P with ICOM tomorrow and check whether there is a plan for it. Then I can attempt to flash using ESYS. What do you think?

Thank you again.

[lynxbmw]

As you already used ista-p on this car, go to dir C:\ProgramData\BMW\ISPI\data\TRIC\ISTA-P\Operation\Log and find file with filename something like VIN_012345_20170918_232815.istap, where VIN is equal to this G11 VIN. Extract this file with 7zip for example and you will see another file with name as VIN_012345_20170918_232815.execTAL.
Open this file with notepad or any prefered text editor and check for shimpent i-level e.g. <bauIStufe>F020-15-03-502</bauIStufe>.
This is how to find the shipment ilevel.

[pweber84]

Yes, I found Shipment I level, it was not a problem as I had report from ISTA when it programming failed. You can see this few posts above.

What is interesting for me now (after BDC_GW was flashed correctly) why ACSM and DME is on RED on ISTA-D. No connection with them.

[hojo29]

Ok, after diagnosing with ISTA-D all ECUs are green, but with ACSM and DME there is no connection (RED). Do you know why? Should I reflash whole car with ESYS or ISTA-P?

I will fire up ISTA-P with ICOM tomorrow and check whether there is a plan for it. Then I can attempt to flash using ESYS. What do you think?

Thank you again.

Take pictures of ESYS when all the control devices were read.

[pweber84]

I will do it tomorrow. Thanks again.

[pweber84]

Hojo29, there is still problem with this G12, can you help via teamviewer?

---

Also, I can't READ SVT, I receive ERROR Generate SVT_ist failed [C105]

How to do TAL calculation and flash car without READ SVT?

[lynxbmw]

Read ECU instead SVT, it's still SVT tree.

[pweber84]

But I can't select I-step shpiment and target. Don't know why. Also ACSM, DSC, DME, EPS, HSR, DME2 SAS, are on RED in ISTA-D.

When I try to use ISTA-P it says REANIMATION, but then STATUS: not EXECUTABLE and red arrow with X. Anyone can help with that? I know that these modules are connected via FLEXRAY. Maybe after flashing BDC_GW I have to initilize flexray?

[jaramillo]

But I can't select I-step shpiment and target. Don't know why. Also ACSM, DSC, DME, EPS, HSR, DME2 SAS, are on RED in ISTA-D.

When I try to use ISTA-P it says REANIMATION, but then STATUS: not EXECUTABLE and red arrow with X. Anyone can help with that? I know that these modules are connected via FLEXRAY. Maybe after flashing BDC_GW I have to initilize flexray?

Some days ago I faced a similar behavior with E-sys 3.28> The I-step shipment and target were not selectable.
So I have to downgrade to 3.27 and It worked flawless.