Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Help F10 2015 High Beam Assist Retrofit (Xenon Only)
12-05-2019, 09:28 AM,
Post: #11
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
|
|||
16-05-2019, 12:34 PM,
Post: #12
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(08-05-2019, 10:08 AM)claw Wrote: After 7/2013 all F10/F11 have at least xenon headlights (no more halogen), so SA522 is not necessary anymore, and is not present in FA. Thank you for letting me know after 2013 BMW decided to be a Bixenon lamp. So now I don't have 522 in FA but I can code VO FRM + FLA and FRM it understands I have Fa 522.? |
|||
20-05-2019, 09:52 AM,
Post: #13
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
Welcome everyone. Update is how to activate HBA with the switch off switch. Thanks for the NCD TokenMaster comparison tool
Who can help me? I Have Coding VO FRM, FLA3 after adding 5AC. Conclude. Only works very well after Coding times. It turns itself off when the engine turns on the next time, I also switch the A-Off - A light switch, it doesn't work again. Note: I choose FDL FRM, do not edit the code (FDL after having 5AC), and HBA works again, I decided to run the test to see if it worked. As a result, it works very well, turns itself on and off high beams according to traffic, but when it stops and starts again, it disappears. I have read somewhere on forums of HBA activation commands 1. / FRM >> FLA_VERBAUT = aktiv 2. / FRM >> FLA_AUTO_AKTIV = automatisch 3. / KAFAS2 >> 3050 >> FLA_ON_OFF = aktiv But I equipped the mirror in FLA3 so I couldn't find it KAFAS2 >> 3050 >> FLA_ON_OFF = aktiv, and I also rummaged in FLA3 nor did FLA_ON_OFF or it changed to another code? I also searched in FRM the following code a. / 3000 FRM_VERBAU_U_ALLGEMEIN, 20 LIN_PUBU_TLC nicht_aktiv (not active) = 00 Comment = BEFAS: Auswertung des Tasters TLC (Time To Line Crossing / Fahrspruverlassenswarnung) am Bedienteil Fahrerassistenzfunktionen b / / 3050 FRM_AUSSENLICHT_PARAMETER, 30 FLA_TASTER_LIN ueber_can = 00 Comment = 0 - FLA Taster Information wird über CAN-Bus eingelesen: SZL ---> FRM 1 - FLA Taster Information wird über LIN-Bus eingelesen: BEL -> FRM " OPTIONS ueber_can = 00 ueber_lin = 01 c. / FLA_BEL_POS stufe_A = 01 Comment = 0: FLA will be activated if BEL is in POSITION AUTO or MANUAL LOW BEAM; 1: FLA will be activated if BEL is in POSITION AUTO Blendfrei nur in A, da auch nur hier die AHL funktioniert OPTIONS stufe_A_und_II = 00 stufe_A = 01 But I'm not sure these commands can automatically HBA. Does anyone know please show me Thank you very much |
|||
31-05-2019, 10:19 AM,
Post: #14
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
No one is holding me. I replaced it myself and HBA did not work.
I replaced only the HBA button because I found it the same (same pin out, same position, same color wire). Attached image How to remove 2 SZL protective covers is relatively easy. Upper part https://www.newtis.info/tisv2/a/en/f10-5...t/1LkAJvrz Bottom https://www.newtis.info/tisv2/a/en/f10-5...t/1LdWJBrt Replace only the circuit and the same button. After replacement I have FA added 5AC and changed Zeitkriterium = 0317 (Zeitkriterium = 0317 I have because of NBT EVO retrofitted), I do not write FA to the car, only activate FA and I make VO FRM, KOMBI, DSC, JBBF, FLA3, SZL After VO, FDL FRM FLA_AUTO_AKTIV = automatisch Unfortunate results, HBA also only works after the code. Turn off the vehicle and open the car again. HBA is not working. The buttons HBA and BC are the same, both HBA and BC have the same BC function as before. Do I need to change the Zeitkriterium the other day? Because of the label on the mirror FLA 01/05/17. Or 2016 F10 LCI cannot activate HBA without HBA button on the steering wheel. |
|||
31-05-2019, 10:38 AM,
Post: #15
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
The circuit inside the SZL is different, you need to switch that one, otherwise it will not work..
Press and if this post helped you.
|
|||
31-05-2019, 12:01 PM,
Post: #16
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(31-05-2019, 10:38 AM)Gizmo520d Wrote: The circuit inside the SZL is different, you need to switch that one, otherwise it will not work.. Thank you for your help I also buy ebay Cluster SZL and am waiting for shipping https://www.ebay.com/itm/BMW-6-Series-f0...2527490848 Let me ask more, If I replace SZL, I only inject CAFD and VO code, it works. Or need to use Ista + to adjust the steering angle sensor. Because I'm afraid Ista + is a software I'm not good at. |
|||
11-06-2019, 12:49 PM,
Post: #17
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(31-05-2019, 10:38 AM)Gizmo520d Wrote: The circuit inside the SZL is different, you need to switch that one, otherwise it will not work.. Hi everybody Do not know what I am missing I replaced the other SZL cluster with HBA button and Open E-sys I Activate FA with 5AC without Save FA to vehicle, VO Code VO FRM, FLA3, SZL HBA button works well Turn on and switch HBA. But I'm still not lucky that when I switch the engine and turn on the car, the HBA button no longer works on / off. I have Isata + call SZL ECU to check the buttons BC and HBA, the signal is good People can pin me, what have I missed? Thank you |
|||
11-06-2019, 14:39 PM,
Post: #18
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
That's strange. Is any error stored?
You can try to flash the szl Press and if this post helped you.
|
|||
12-06-2019, 00:45 AM,
Post: #19
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(11-06-2019, 14:39 PM)Gizmo520d Wrote: That's strange. Is any error stored? I have no errors in Isata +. The HBA button also works well (on / off) after VO code or Edit FDL ECU FRM (only Edit FDL Code FRM face even if there is no change in FRM). But the HBA button does not work when the engine starts next time I think that in the ECU FRM command there is something that switches HBA or does not wake the HBA. |
|||
12-06-2019, 08:27 AM,
Post: #20
|
|||
|
|||
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
Try VO coding for the KOMBI aswell. There are also some parameter which needs to be changed there.
KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_APPL = aktiv KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_TIMEOUT = aktiv KAFAS > FLA_CODING 3015 > FLA_ON_OFF = aktiv JBBFE > FZM_EnergyDataMemory_FeTra_LIN 3200 > LIN_VARIANTE_INNENSPIEGEL = nicht_aktiv [Default] FRM__03CT > FRM_AUSSENLICHT_PARAMETER 3050 > FLA_VERBAUT = aktiv Press and if this post helped you.
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content