[Node]

Your problem is: Subnet mask does not match with subnet mask of master gateway. That is the reason it can't switch to http. You need to check the network settings in a gateway unit and compare to the ones in your computer.

[Krysiaman]

How can I check settings in gateway?

I tried now on Enet cable and it throws me this: 

Code:

<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>

<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<[] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [WARN]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>
<[HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>

 

Slightly different

[Node]

You can't just switch from ICOM to ENET as ICOM has DHCP server and provides different address range to gateway. Of course you could have DHCP server on your ENET and it could work. Given you had the previous error with ICOM it is possible that someone did some changes to IP config of gateway before. I think best way for you is to disconnect the car battery for a minute so gateway resets it's IP configuration.

[Krysiaman]

Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch

[Node]

There are functions in tool32 for BDC to set IP address, mask, etc. I just don't remember what they are called. It could be someone changed default setting or something.

[dasi]

Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch

can you ping 169.254.199.99 ?

[Krysiaman]

Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch

can you ping 169.254.199.99 ?

nope

   
   

Checked OABR and it's connected. Pin 1 and 3 goes to BDC. There is also something more in EVO OABR but I assume it's ATM.

EDIT:
Just checked ipconfig using DEV_UDS:

Code:

  STAT_IPADDRESS                  = 169.254.199.99

  STAT_NETMASK                    = 255.255.0.0
  STAT_GATEWAY                    = 0.0.0.0
  JOB_STATUS                      = OKAY

[Krysiaman]

Just thinking:
Could it be bad BDC? There was only one BDC hardware version for whole G30 range?

[Node]

And what is the config of your computer???

[Krysiaman]

Looks like my problem is somehow gone. When I use router (real, not software) and always disconnecting battery for a while before connecting icom and ista/esys I don't have any issues with Ethernet and programming goes fast. Tried today on F06 with EVO. When I started programming using build-in ICOMs DHCP server programming was very slow. I have aborted it and then connected via Router and also disconnected battery for a while and then it went in normal speed



And about that exact G30 which didn't want to ping IP: there actually was a problem with OABR. Fixed wirings and everything works fine