Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
KL15 & R contact switch CAN commands
30-12-2017, 21:51 PM,
Post: #21
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
I had a look at my program and I did it not with a single message because there is a message with a time depending incrementing value.
If you want, I can give you the program for an Arduino, but for CAN1 there is no CAN shield ready to buy, I soldered it by myself. |
|||
01-01-2018, 11:35 AM,
Post: #22
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(30-12-2017, 21:51 PM)gt678 Wrote: I had a look at my program and I did it not with a single message because there is a message with a time depending incrementing value. Okay, it will be very interesting! Happy New Year! |
|||
02-01-2018, 22:00 PM,
Post: #23
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(30-12-2017, 10:29 AM)Loliceman Wrote:(30-12-2017, 08:33 AM)hero3838 Wrote: Yes but you can not code nbt directly in car you have to code it on bench i .now i connect nbt k-can2 line from my orginal zgw01 it works but only rear view camera and side view dont work and some buttun on panel (radio on/off mute ,mode, eject cd, and arrows left right also steering whell control for up down) other all funcuon ok .and i will order kcan to kcan2 bridge i will try with can bridge .most emulator is expensive almost a nbt price 450 euro + shipping . I rerouted wires but same issue. Camera doesn't work .but when i replace zgw with flashed one camera works. I am waiting canbus bridge (k-can to k-can2 convertor) i will try converting kcan data and will see . |
|||
03-01-2018, 15:15 PM,
Post: #24
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
Here is a list with Ibus commands. Takes a little time to understand, but eventually it is easy.
http://web.comhem.se/bengt-olof.swing/IBus.htm |
|||
03-01-2018, 17:37 PM,
Post: #25
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(03-01-2018, 15:15 PM)KahN Wrote: Here is a list with Ibus commands. Takes a little time to understand, but eventually it is easy. Thank you a lot! I'm not sure that it's suitable for E6x CAN bus, but it will help me anyway. Thank you again! |
|||
04-01-2018, 10:39 AM,
Post: #26
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
I have a bench for e serie with CAS, KGM and Key.
Ignition ON and OFF is no problem. i have a second bench for f serie with CAN BRIDGE from carsystems and ZGW02 8SK but here cant Ignition OFF sad i need this for NBT correctly off. what can i do? |
|||
04-01-2018, 11:52 AM,
Post: #27
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(04-01-2018, 10:39 AM)Emmy Wrote: I have a bench for e serie with CAS, KGM and Key. I can't think of any reason why you need to have ignition OFF for your NBT bench? But, If u need it to stop sending ignition ON, just disconnect either CAN_L or CAN_H / power 12v from your CAN Bridge? Please, Press the Buttons and if you feel that this post helped you!
|
|||
04-01-2018, 15:10 PM,
Post: #28
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(04-01-2018, 11:52 AM)Loliceman Wrote:(04-01-2018, 10:39 AM)Emmy Wrote: I have a bench for e serie with CAS, KGM and Key. disconnect CAN bridge dont works. display goes off but NBT keeps going. i need this.. i have my reasons |
|||
06-01-2018, 19:32 PM,
Post: #29
|
|||
|
|||
KL15 & R contact switch CAN commands
Hi can you send me the can sheild info please I would like to make a bench setup for e series.
I have 1 for f series thanks Sent from my HTC One X9 using Tapatalk |
|||
06-01-2018, 23:35 PM,
Post: #30
|
|||
|
|||
RE: KL15 & R contact switch CAN commands
(04-01-2018, 15:10 PM)Emmy Wrote:(04-01-2018, 11:52 AM)Loliceman Wrote:(04-01-2018, 10:39 AM)Emmy Wrote: I have a bench for e serie with CAS, KGM and Key. If you think with your brain. This is exactly what happens when u take ignition off... The headunit stays on for a few minutes.. oh gosh Please, Press the Buttons and if you feel that this post helped you!
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
modifying the BMW x3 g01 light switch | boweld11 | 4 | 238 |
15-05-2024, 11:20 AM Last Post: kimz |
|
Is it possible to switch between rear-view and side-view in 5DL? | lacost | 0 | 72 |
07-05-2024, 16:58 PM Last Post: lacost |
|
X5 E70 KL15=0 after attempted theft | PUMUKY1 | 9 | 507 |
11-03-2024, 01:43 AM Last Post: PUMUKY1 |
|
g20 driver's switch block | redog4dy | 5 | 401 |
23-11-2023, 19:25 PM Last Post: redog4dy |
|
Mini R56 KL15: 0 | PUMUKY1 | 9 | 558 |
16-11-2023, 18:58 PM Last Post: Dirchik |
|
ISTA switch | Node | 26 | 4,055 |
14-11-2023, 22:18 PM Last Post: DarkSide |
|
Coding Tailgate Free contact (Retrofit) | ruben_17non | 2 | 318 |
27-10-2023, 09:08 AM Last Post: ruben_17non |
|
BMW part number for connector contact | Vojno | 4 | 613 |
03-10-2023, 08:22 AM Last Post: schaeublew |
|
KL15 voltage Icom | VroomVroom | 1 | 262 |
17-09-2023, 20:46 PM Last Post: Esysx |
|
BMW F10 M5 gear selector switch retrofit on regular F10 | leungsk1 | 12 | 1,778 |
14-08-2023, 18:47 PM Last Post: mrpetesingh |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content